Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (August 2008, week 5)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 31 Aug 2008 19:38:00 -0400
Reply-To:     Robert Stewart <robertmstewart@MAC.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Robert Stewart <robertmstewart@MAC.COM>
Subject:      Re: Head leak - What is the process for using Bars Leak Head
              Gasket Repair
Comments: To: pickle vanagon <greenvanagon@GMAIL.COM>,
          Matt Sutton <msutts@earthlink.net>
In-Reply-To:  <91c8f9760808311522i7c16c3f0wc9f2062ddc88fdec@mail.gmail.com>
Content-Type: text/plain; charset=US-ASCII; format=flowed; delsp=yes

Which coolant tube do I remove from the thermostat housing for the flushing? I see three of them. Right, left, center?

The one on right side that goes up into the body of the van toward the right?

Or the one on the left? Need some assistance please?

Also there has been talk of the T stat - I assume that when the front Fan on the van goes off that means the T stat has opened?

Robert

On Aug 31, 2008, at 6:22 PM, pickle vanagon wrote:

> On a vanagon, you would pour into the coolant tank inside the engine > compartment (Not the expansion tank, but the one connected to it > with the pressurized cap and the coolant level sensor). > > To flush the system, you can stick a garden hose into one of the > coolant hoses, put a rag around the hose to cut down and back flow, > and send water through the system until it comes out the other end > clean. Don't send too much pressure, and make sure there's no gunk > in your garden hose. Maybe someone else will chime in on which > hoses it is best to do this with. > > Don't skip the flushing. There's a lot of antifreeze hidden in the > vanagon system, I think the bar's leak stuff will gel up if you > don't get it out. > > -Wes > > On Sun, Aug 31, 2008 at 6:04 PM, Robert Stewart <robertmstewart@mac.com > > wrote: > Hey Matt, > > Just wondering what the process for the installation of the bars leak > stuff was? > > I just bought their head gasket leak repair and it says to pour it > into the radiator and not the coolant tank? > > What did you do? Does anyone know this should be done with our Vans? > > It also suggested a flush using a T coolant attachment, did you you do > this? Where did you connect the hose with the T system? > > Thanks, > Robert > NYC > > > On Aug 6, 2007, at 2:17 PM, Matt Sutton wrote: > > Hi All, > > Perhaps just anecdotal evidence, but my experience matches Ken W.'s > (actually, I think it was he who recommended Bars Leaks to me in the > first > place). Heads had been done at 70k by the PO, and I had a little > seepage at > 160k. I used the liquid Bars Leaks, about 3/4 the recommended dose for > caution's sake, and have been dry ever since (now at 225k). No > radiator/ > heater core problems came up. Also, just replaced the large driver's > side > water pipe in the engine bay this weekend, and the interior was > pristine > (except where rust had eaten through from the outside). > All this with regular prestone, for what it's worth. > > Best, > > Matt Sutton > 88 Gl > Brooklyn NY >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.