Date: Sat, 22 Nov 2008 11:38:45 -0800
Reply-To: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject: Re: CV joints...condition?
Content-Type: text/plain; format=flowed; charset="Windows-1252";
reply-type=original
HI Don,
Sounds like you're on the right track. Assuming the idea is to stretch out
the life of the good CV joints and your money .............your idea of
replacing the two really bad ones and lubing up the remaining 2 'not totally
shot' ones is a fine idea.
Given that they don't fail totally and catastrophically...........re-using
decent used ones is fine with me. If I have any concern for a big trip, I
just carry one spare CV joint. They're not that hard to change. I also
upgrade to the 12 point screws often. They normal 6 mm allen screws strip
out quite easily. I also use a cold chisel and a hammer to unscrew the
stripped out ones - not that hard to do at all. Though, I havn't seen many
long cold chisels like the one I use on stripped out outer CV joint screws.
A normal short cold chisel is perfect for the inners, when needed.
I've seen the 'really running thin grease' syncdrom on a few CV joints. I
believe it's possible that gear oil could find it's way into the CV joint -
that might be an explanation. Or perhaps cheap grease was put in there eons
ago. I use 'black slimey' moly grease on all my CV joints. I put a fair
amount in there too............
I don't exactly jam pack the boot, but I put a generous amount of grease in
there, and in the 'cup' of the flange the joint bolts too. When I screw
them down some extra grease always squeezes out. I've seen quite a few dry
CV joints too, almost like the grease evaoporates, or people just didn't put
enough in.
If you look at the innner part where the balls push, you can see that they
wear on one side, and not the other. That means if we install it so it's
being driven the other way ..........we can get the balls to push on a new
surface, thus extending teh life of that particular joint. I always mark
my axles for which side they were on and which direction is 'forward
turning' before removing them- to keep track of which joints were innor or
outer, and which way they were driving.
Why they're made like they are ?
- seems like a pretty clever and obvious device to me. A CV joint not only
provides the 'universal joint' affect - transfering drive of a rotating
shaft through an angle, and one that varies too...........but there is also
length compliance. And of course..............with the rear wheel going up
and down on bumps............there has to be a provision for length change
in the axle. On earlier designs.......like the rear of a Jaguar, where they
used conventional cross type J-joints........the axle was in two sections
joined by a sliding coupling arrangement, to account for length change. The
CV joints take care of that by themselves - quite elegant actually.
Scott
turbovans
----- Original Message -----
From: "Don Hanson" <dhanson@GORGE.NET>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Saturday, November 22, 2008 11:00 AM
Subject: CV joints...condition?
> Finally dove into the task of checking, servicing and possibly replacing
> the
> CV joints on my 84 manual 5-sp tranny. Been putting it off because I was
> just sure I would strip out a couple of the allen head bolts. About 2 wks
> ago, I began 'basting' the bolts with Liquid Wrench and surprise, they all
> came out without a hitch.
> The joints were varied as to the condition and since I've not done this
> task before, what am I looking for/at? I've read the write-ups online.
> Two CVs on the drivers side axle are obviously shot, for sure. They had
> chunks out of the bearing races, a couple of the bearings are badly pitted
> and the one at the wheel end, that one had almost 'liquid' grease, unlike
> all the others. The others, the grease was really dry..about the
> consistency of fudge brownies. But that one, the grease actually dripped
> out..What's up with that? I can't see how anything could be getting in to
> dilute the grease..
> The ones on the other axle: One was pretty nice..dry but fine looking.
> The other has some discoloration of the bearings but no pitting of any of
> the races...just looks like it's been hot..4 of 6 of the bearings are
> kinda
> brown/blue not shiny silver, but they are smooth and undamaged..Should I
> expect this one to fail soon, or can I just replace it next time..I plan
> on
> servicing these yearly now (about 20k miles of driving for me).
> So, I am doing two of these for sure..the ones with the pitting and
> galling of the races. One looks as new almost, and one has some evidence
> of
> the bearings taking some heat...I'd like to defer replacement on that
> side,
> if I can get away with it. Yes? No?
> Odd critters, the CV joints. I can usually look at a mechanical device
> and deduce why it is made like it is, etc etc. Not the CV joint...It
> seems
> a bit arbitrary, why things are shaped as they are and how it fits
> together...Not that I 'studied' it or anything..
> Don Hanson
>
> ------------------------------------------------------------
> + To unsubscribe from the Vanagon List send an e-mail to
> + listserv@gerry.vanagon.com with SIGNOFF VANAGON
> + in the body of the message.
> ------------------------------------------------------------
------------------------------------------------------------
+ To unsubscribe from the Vanagon List send an e-mail to
+ listserv@gerry.vanagon.com with SIGNOFF VANAGON
+ in the body of the message.
------------------------------------------------------------
|