Date: Sat, 22 Nov 2008 14:15:17 -0800
Reply-To: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject: Re: Clutch on 84 Westy
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
the trans and bell housing will only come out as one piece. ( you can only
get the bell housing off the transmission with the trans out of the van ) .
You just 'remove the transmission' ...........that's the easiest and most
direct way to get to the clutch.
I just did a clutch job the other day, and I opted to take out the engine
instead...........cause then you have the clutch right in front of you while
you're working on it on the engine, rather than doing that all under the
van..........bit more work that way, but it's a 'cleaner' job that way, no
CV joint grease in your hair, etc.
tips ? .........
it's a good time to service the CV joints, if the trans is coming out. I at
least add some moly grease to inner CV joints.
oh, here's another one. I find the pilot bearing shot in at least a fourth
of the vangon clutches I see.
And commonly the little metal ring that is pressed into the flywheel, that
holds the felt pilot bearing dust seal in place, is missing, and thus the
pilot bearing is just rusty dust and totally gone even.
I figure that shops send the flywheel out for resurfacing. The machine shop
removes that little ring, then they throw it under on of their workbenches,
never mention it to the shop, the shop never thinks about a pilot bearing
dust seal when they put it back together, and then the pilot bearing is shot
in about 2 or 3 years. You can't get that little metal ring separately
either, not that I've been able to find. I have about 6 flywheels missing
that little part.
Lube everything that moves, pivots, or slides in the throw out bearing
cross shaft area. That means the guide tube the TOB slides on, the tips of
the forks where it rides,.........and spray lube the cross shaft where it
pivots in the bell housing until it moves easily and smoothly. Lube the
ball pivot at the tip of the cross shaft lever where the slave push rod
pushes on it.
I always change the clutch hydraulic fluid too - i.e. bleed the clutch
hydraulic fluid. That should be done every two years anyway. I get a 'new'
used vanagon in stock, and that's one of the first things I do to it
..........quite often people never change the clutch hydraulic fluid, and it
should be done every two years just like brake fluid.
Do perfect workmanship. I am not kidding you...........almost ALL work I
see done on vanagons by shops is sloppy or short somehow. Things left off,
foreign things left in the area etc. etc.
Have fun, do good safe work !~
Scott
www.turbovans.com
----- Original Message -----
From: "John Houser" <JohnHJhouser@AOL.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Saturday, November 22, 2008 11:20 AM
Subject: Clutch on 84 Westy
> The clutch on my 84 Westy got where it won't disengage. There are no
> visible leaks on the master or slave cylinder and the slave cylinder
> appears to
> extend correctly.
>
> I have the LUK rebuild kit from Bus Depot. I'm looking for advise on doing
> the clutch rebuild. Do I remove the transmission and the bell housing
> together or separately? Any time/labor/finger saving tips?
>
> TIA,
>
> John Houser
> Perry, GA
> **************One site has it all. Your email accounts, your social
> networks,
> and the things you love. Try the new AOL.com
> today!(http://pr.atwola.com/promoclk/100000075x1212962939x1200825291/aol?redir=http://www.aol.com/?optin=new-dp
> %26icid=aolcom40vanity%26ncid=emlcntaolcom00000001)
>
> ------------------------------------------------------------
> + To unsubscribe from the Vanagon List send an e-mail to
> + listserv@gerry.vanagon.com with SIGNOFF VANAGON
> + in the body of the message.
> ------------------------------------------------------------
------------------------------------------------------------
+ To unsubscribe from the Vanagon List send an e-mail to
+ listserv@gerry.vanagon.com with SIGNOFF VANAGON
+ in the body of the message.
------------------------------------------------------------
|