Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (January 2009, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 3 Jan 2009 12:31:18 -0500
Reply-To:     Mark A Kippert <vanagon@KIPPERT.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mark A Kippert <vanagon@KIPPERT.COM>
Subject:      Re: Removing the axle shafts (was: Towing a Vanagon)
In-Reply-To:  <010320091647.19688.495F968D0006FEF700004CE82215553894CECFCFCD9F9D0EBCB6@comcast.net>
Content-Type: text/plain; charset=US-ASCII; format=flowed; delsp=yes

The thought scares me too. The van I'm picking up is two hours away. Looks like I'd need to haul quite a few tools, jack, stands and additional stuff for safe support. Then there is hoping it will come apart without any trouble.

All to haul the van with my Master Tow dolly (which I own and can safely pull the van). Since the van's an automatic I have to pull the shafts. Wish I could put the rear on the dolly but that, I understand, could be problematic.

I'm guessing the smart, EASY, thing to do is rent a car hauler from U- Haul for $50. My concern is the trailer weighs 2000lbs according to U- Haul and the van is near 4000lbs. My Ford Expedition has a Max tow capacity (by the book) of 5900lbs.

Does anyone know how much a stock 1987 2WD GL weighs?

-Mark K

Frankly the smart On Jan 3, 2009, at 11:47 AM, John C... wrote:

> Mark, > Jack Stands in a frozen snowy field > is causing the hair on the back or my neck to stand on end !!! (none > on top to stand :o) > Double Jack Stand It, I say, > Or take the time to Also Block it up > with Wood Blocking !!! > Be Safe! > JC... > > -------------- Original message -------------- > From: Kim Brennan <kimbrennan@MAC.COM> > >> No, there is definitely room to get at the bolts from the other side >> of the swing arm (i.e with removing the axle). You'll want to put >> your >> vehicle up on jack stands and remove the wheel to do this. You'll >> need >> to rotate things too as you remove the bolts (you usually can get >> to 2 >> at a time without too much difficulty.) >> >> I find it preferable to take the inner bolts off the transmission >> first, then remove the bolts off the axle end. I use a long pry bar >> in >> between the wheel studs to prevent rotation of the shaft while >> loosening the bolts. >> >> >> On Jan 3, 2009, at 1:11 AM, Mark A Kippert wrote: >> >>> In looking at the diagram on page 42.2 the axle shaft passes thru >>> the >>> boxy portion of the trailing arm. This being the case it doesn't >>> look >>> like you can get access to that end of the axle without pulling the >>> wheel bearing housing. Is this true (I have not had time to crawl >>> under my van to see)? >>> >>> I'll be laying in a field, under the van, on a cold winter day to do >>> this so the less time I spend laying under there the better.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.