Date: Mon, 2 Mar 2009 22:19:51 -0500
Reply-To: "Jack R." <jack007@COMCAST.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: "Jack R." <jack007@COMCAST.NET>
Subject: Re: what to do when you have the fridge out?
In-Reply-To: <ACDEDD88BB544144B12FDF7A9B27BE63@ZoltanPC>
Content-Type: text/plain; charset="us-ascii"
I highly recommend this stuff!!!
http://www.b-quiet.com/ultimate.html
It is easy to install, deadens sound, insulates, and the backing blocks
water.
Here is a photo of my van in the restoration process, with the b-quiet
installed in the front door.
http://www.flickr.com/photos/77623993@N00/1084874967/in/photostream/
Jack
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
Zoltan
Sent: Monday, March 02, 2009 9:48 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: what to do when you have the fridge out?
Use anything that does not absorb water.
Z
----- Original Message -----
From: "Stephen Grisanti" <bike2vcu@YAHOO.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Monday, March 02, 2009 2:09 PM
Subject: Re: what to do when you have the fridge out?
I used more of the same type (R13 pink stuff) from Lowe's but others use
Reflectix, the thin silver bubble stuff. There may be further alternatives.
Stephen
--- On Mon, 3/2/09, craig cowan <phishman068@GMAIL.COM> wrote:
From: craig cowan <phishman068@GMAIL.COM>
Subject: Re: what to do when you have the fridge out?
To: vanagon@GERRY.VANAGON.COM
Date: Monday, March 2, 2009, 4:58 PM
What do you guys use for inslulation back here instead of the stock stuff?
-Craig
'85GL turned Westy
On Mon, Mar 2, 2009 at 4:43 PM, Bill Glenn <idahobill@gmail.com> wrote:
> Florian,
> 1. Definately clean out the combustion chamber, but be aware that the
> gasket is no longer available from Dometic, so exercise care in separating
> the two halves of the combustion chamber. Since I found the gasket
lacking
> in resiliency, and its ability to seal quesionable, I used a very thin
film
> of gasket sealer on re-assembly.
> 2. Confirm that the drain tube is free of obstruction.
> 3. Check the thermo switch that is mounted on the upper cooling fins, for
> reasonably good contact with the fin; sometimes the retaining ring becomes
> loose. Some thermo-conducting paste can be added between the fin and the
> switch, but that's optional.
> 4. With the fridge powered temporarily with 12 volts, the operation of the
> thermo switch can be checked by applying heat with a heat gun or hair
> dryer; obviously this allows checking the operation of the fan also.
I'm of
> the opinion that if the original fan is working as it should, that's
all
> that's needed. Design Note: the thermo switch is supplied with 12
volts
> whether the fridge is turned on or not, so the switch, and thus the fan,
> will be activated by high enough ambient temperatures.
> 5. Blow out the intake and exhaust tubes.
> 6. Though I can't say for certain, I seem to remember that when
installing
> the check valve update kit, the directions to enlarge the inlet and outlet
> (Bentley 76.26) contained an error with respect to the size of drill bit
to
> use, too large a bit for the job I think.
>
> Unrelated to the fridge proper:
> A. If you use the city water supply, check the plastic elbow for cracks.
>
No virus found in this incoming message.
Checked by AVG - www.avg.com
Version: 8.0.237 / Virus Database: 270.11.6/1980 - Release Date: 03/02/09
23:02:00
|