Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 2009, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 7 Mar 2009 14:25:45 -0800
Reply-To:     Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject:      Re: Heater Hoses
Comments: To: Jon Kanas <kanas@QADAS.COM>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
              reply-type=response

my comments......... be sure it's not the plastic distribution box.........they like to disintegrate where the hoses clamp on. ( I get rid of the spring clamps too.......they are dangerous practically, and can't squeeze well enough eventually. A high quality screw-clamp you can always check and tighten a bit. )

I am a huge, huge believer in taking it apart first, find out what all is tired or broken, THEN order the needed parts. 90 % of the time it's 'more' or 'something else than you thought' after you get in there if you try to get the right stuff before taking apart and examining carefully. The ideal cycle is........take it apart, identify all the bad parts, let the van sit right there apart while you get the parts, then fix it........ the down time is longer, but there's less time wasted on not getting all the parts really needed, not seeing the whole real story etc.

The hoses that wear most are the ones that run hottest. On a typical front engine, front radiator car - that's always the upper radiator hose. Vanagons and syncro's don't seem to have anything exactly comparible........I find that pretty much, the main hoses seem to last just forever, almost. I even suspect sometimes that what we can get these days, is not as good as the original stuff. My personal style is to carry some s spares on trips....... including a bag of generic hose peices and junctions...........but more or less, I like the OE stuff and hoses the most, and keep them in service unless there's a real reason not to.. And there is the 'leave well enogh alone factor too' ..........so kinda half of one, 6 of the other........and I strongly do not recommend 'just replace everything' .........just the stuff that actually is tired or weak.

and the *plastic* ......those parts are weak ones , and they do crumble and disentigrate with heat and age. Those need to be 'not the origina ones l' pretty much. Interesting that on the syncro they put on a metal thermostat housing instead of the plastic one on 2WD vanagons with the 2.1 engine......at least they got that right.

If you trace where the heater hoses actually go under a syncro, .........it's quite amusing. There's one that goes forward, then across, then back, or someething like that. If someone sells a true kit of real OE grade syncro-specific heater hose, that would be nice to install.

I think I'd convert mine to all readily aviable generic high quailtiy heater hose though.........for easy repair in the future, assuming I could do a neat and solid job at it. I know I would sure move the fuel filter ! Scott www.turbovans.com

----- Original Message ----- From: "Jon Kanas" <kanas@QADAS.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Friday, March 06, 2009 10:24 PM Subject: Heater Hoses

> Hello Listers, > > Vehicle: 1987 Syncro, 121K Mi. > > Weather's nice, so it's time to get the Syncro out and prepare for some > fun. That being said, I've a coolant leak. There is a wet coolant on > the heater hose at the rear, immediately over the RR axle. The leak is > either at the very end of the hose where it couples to the "Distribution > Unit" (See Bentley, page 19.11, diagram 19-427). It is not readily > apparent which component is leaking. > > Question 1: Is the "Distribution Unit" sufficiently trouble prone to > justify more extensive diagnostics, or would one proceed on the > assumption that the hose is at fault. > > Question 2: The heater hoses feel soft, and have never been replaced. > What is the list's collective list experience with the lifetime of > Vanagon heater hoses. > > Question 3: I am thinking about replacing all of the heater hoses. I'd > appreciate recommendations for "kits" from any of the list vendors which > are complete, with good quality components. I reviewed the archives, > and understand that there are some nuances to the heater hose sizes that > encourage me to want to purchase a complete kit, if possible. > > Question 4: A couple of years ago, I had a leak from one of the > itty-bitty coolant hoses at the oil cooler. I've replaced both of > these. Given that one of these failed, and now the heater hose(s) are > suspect, should I be thinking about replacing the big coolant hoses > too? They are not nearly as soft as the heater hose(s), but pretty > pliable. > > > -- > > *Best Regards, > Jon B Kanas > Home: 303-678-0658 > Mobile: 303-746-1785 > Email: kanas@qadas.com <mailto:kanas@qadas.com> > Website: http://www.qadas.com/~kanas <http://www.qadas.com/%7Ekanas> > *


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.