Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (March 2009, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Tue, 10 Mar 2009 06:57:25 -0700
Reply-To:     dylan friedman <insyncro@YAHOO.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         dylan friedman <insyncro@YAHOO.COM>
Subject:      Re: Manual trans replacement
Comments: To: Sam Walters <syncrosam@GMAIL.COM>
Content-Type: text/plain; charset=iso-8859-1

The big if is IF you can remove the clutch lever from the shaft. I am 50 50 on removing that part. dylan ________________________________ From: Sam Walters <syncrosam@GMAIL.COM> To: vanagon@GERRY.VANAGON.COM Sent: Tuesday, March 10, 2009 7:27:13 AM Subject: Re: Manual trans replacement From:  "Tim King" <tking_ms@h...> Date:  Mon Oct 1, 2001  2:57 am Subject:  Re: [Syncro] Time to change out the slave cylinder...(another removal tip) ADVERTISEMENT Hey Folks, I've got a slave tip that will save you some time on this. Brent, sorry I didn't see this earlier, but just got back into the country. (Three weeks in France. Boy French vehicles have come a long way. We had a diesel Renault Laguna that was frankly sweet. Only saw about five vanagons the whole time, but many many other delivery-style vans.) Anyway, I digress... I got a tip from Daryl at AA transaxle that makes removing the slave on a syncro a snap. Basically, you just remove the slave bracket from the tranny by removing ONE snap ring then the clutch lever. 1. Move slave shaft/boot off clutch lever ball. If your slave is totally shot, you can usually just push the slave cylinder shaft/boot off the ball on the clutch lever. If it's a good slave (say you are just R and Ring the tranny), you may need to open the bleeder to make it easy to remove. Just lever it free, then let it hang free. 2. Wiggle the clutch lever off the shaft. If it's been there for a while, you may need some liquid wrench or something, but it should come off by hand. 2.5. Unbolt bracket supports and hose retainers from tranny (above CV shaft). 3. Pull the bracket and slave off as one unit. 4. Pull the unit down under the van (you put it on ramps, right?) and work on it where you have access to it from both ends and room for standard wrenches. You may need to remove a couple of the hose clamps holding the hose to your tranny to give you more slack. 5. Bolt on new unit and install in reverse. 6. Pressure bleed system and hit the road. Using this method takes about 30-40 minutes total, assuming you are using a pressure bleeder like Brent recommends. Note: I'm not sure if it's syncro specific -- I think it requires the flexible plastic fluid lines of the syncro, something my 83 vanagon was lacking. Have fun. This tip from trannyman extraordinaire Daryll at AA transaxle makes a drag of a job a LOT easier. Tim King Seattle, WA 87 Syncro Westy     ----- Original Message -----     From: Brent Christensen     To: Syncro@yahoogroups.com     Sent: Monday, October 01, 2001 5:31 AM     Subject: Re: [Syncro] Time to change out the slave cylinder...     Well, I did the nasty deed and replaced the slave cylinder yesterday morning.  Not all that bad, really.  Dr. Rainer's tip sheet (which I have left attached to this e-mail) was very helpful as a road map, but I would offer the following additional advice to anyone planning this job:     First, having a pressure bleeder made bleeding the system a 5-minute one person job.  If you don't have one already, run out and get one.  I have a unit called an "Eezi-bleed" that I bought years ago for an Austin Healey - about $30 and it is pressurized by a tire (I use a wheelbarrow tire with about 25 psi in it).  A quick search turned them up at http://www.aep.bigstep.com/Eezi.htm     Secondly, a 13 mm  "Crows foot" at the end of a long 3/8" extension worked WONDERS for removing the pesky rear bolt (the one towards the reat of the van).  Forget trying to do it with box wrenches, unless you have a "super stubby" like Snap-On makes, or you are willing to make your own by cutting it in half and grinding the stub smooth.  Another ideal tool would be a 13 mm "distributor wrench" but I was not able to find one, and don't even know if they are made in 13 mm.     Removing the Slave cylinder entirely from the topside is possible, and I would submit, easier.  In fact, if you are lucky, you could do it without ever crawling under the van at all.  The trick is to undo the banjo fitting at the slave cylinder, which is a bit tricky if you have thick fingers.  You have to force the short coolant hose back far enough so that you can back the bolt out from the banjo nut.  Be prepared, as all the fluid will then leak out from the system, which for me was nothing, since the slave had failed and dumped all its fluid already.  (Also, having a pressure bleeder, I was not worried about introducing air into the system).     The most difficult thing about reinstalling the new unit (which I did as an entire assembly - shaft, boot and cylinder) is getting the nuts started.  When you drop the slave in place, the rod rests against the clutch's throw-out arm (or whatever you want to call it).  This means that the unit wants to sit about 5 mm above its mating surface unless you apply some force, which then compresses the spring inside the cylinder (which is still empty of fluid).  Once the rear nut is started by hand (I used a 13 mm combination wrench slipped in underneath the bolt head to hold it in place, which is tricky) you can crank it down about 1/2 way by pushing the slave down against its mating surface and rotating the nut with your forefinger and middle finger.     Once the slave is secured like this, you can start the forward bolt from underneath (you have to do the rear bolt first, since the only way to put it into position from underneath is to use the hole that the slave cylinder fits into).  Start the nut by hand, then reach in with a long extension and "wobble socket" or 13mm socket on a 3/8" knuckle.  With a wobble socket, there is sufficient clearance - with a knuckle + socket it could be pretty tight.  I was able to completely tighten the forward bolt this way after reaching underneath and placing a box wrench around the head of the bolt and  resting against something.    A couple more turns on the rear bolt head with the crow's foot and the cylinder was in nice and snug.     Next comes the banjo fitting, which was surprisingly easy to get back on.  I pulled back the aforementioned hose and gently started the bolt with a couple of fingers twiddling at it until the threads caught, then tightened it down with a 17mm open end wrench.  Tightened it up and then fit a small plastic tube to the bleeder screw, running it down to an empty brake fluid can propped in the engine bay.     Next, I fitted the pressure bleeder, attached the wheel barrow tire, and then went back and opened the bleeder screw.  I stood and watched the bubbled dribble out of the system while I opened my first beer (when was the last time you did *that* while bleeding a hydraulic system?).  After a couple minutes and no more bubbles, I checked the pedal.  No pedal, so I pumped it slowly about 10 times and turned the bleeder on again by reapplying the air pressure from the tire.  About 30 seconds later another batch of bubbles came out, so I shut everything down, cleaned up, and tool it out for a test drive, everything working beautifully.     Total time for job:  About 2 hours start to finish,  not including setup and cleanup.     Brent Christensen     Santa Barbara, CA         >     >     >Removing the Clutch Slave Cylinder     >----------------------------------     >     >1. Even though the clutch slave cylinder is held by only two bolts, it's     > a bear to remove. First thing you should do is to apply generous     > doses of WD40 or similar to the two bolts. And since, if mounted     > correctly, the bolts are sitting there with their heads down and     > their shafts up, the best way to apply the WD40 is from the engine     > compartment. And while you are there, also remove the tiny rubber     > cap on top of the bleeding valve of the slave cylinder before it     > might get lost in the process of the removal.     >     >2. The flexible hose leading to the clutch slave cylinder is attached to     > the frame of the van by two clamps. Remove both these clamps from     > the van.     >     >3. The front bolt holding the clutch slave cylinder is best removed from     > below the van with a 13mm socket on top of a long extension while at     > the same time holding the nut with a 13mm wrench. The shorter that     > wrench, the better. The real problem, however, is the rear bolt.     > Push up the rubber boot protecting the push rod for the clutch lever     > as much as possible. This way you are then able to access both ends     > of the rear bolt from the engine bay. Sneak in a 13mm wrench in     > order to hold the head of the rear bolt and remove the nut using     > another 13mm wrench. Again, the shorter this wrench the better, and     > a flat box wrench is probably suited best, because it will fit every     > 30 degrees.     >     >4. When the two bolts are removed dive under the van again, pull the     > push rod out of the rubber boot at the lower end of the slave     > cylinder and also gently pull the rubber boot from the slave     > cylinder. If necessary use a small screw driver to convince the boot     > of letting go. Finally carefully find a path between tranny, fuel     > tank, slave cylinder mounting bracket, half axle, coolant and exhaust     > piping, and maybe some other things to bring the slave cylinder down,     > so it will hang on its hose right below the tranny.     >     >5. In order to minimize the loss of brake fluid you should now remove as     > much brake fluid from the reservoir in the instrument cluster on the     > dash as is necessary to lower the brake fluid level below the hose     > entering the reservoir from the right. This way opening the hose at     > the slave cylinder will not drain the reservoir any more.     >     >6. To disconnect the hydraulic fitting at the end of the hose from the     > slave cylinder you need something to catch the hydraulic fluid still     > in the hose, as well as a 17mm box wrench, a piece of wood, and a     > hammer. Put the box wrench on the head of the hyraulic fitting in     > such a way that wrench and slave cylinder form a rather flat     > triangle, cylinder to the left, wrench to the right, and the head of     > the hydraulic bolt pointing towards you. Place this triangle on the     > piece of wood and then carefully hammer on the eye of the wrench,     > flattening the triangle even more and thus loosening the bolt of the     > hydraulic fitting. Be prepared to catch the brake fluid which now     > starts oozing out. Remove the hydraulic fitting altogether and make     > sure not to lose the two copper washers sitting on the hydraulic bolt     > on either side of the hydraulic eye. Drain the rest of the brake     > fluid from both, the hose and the slave cylinder (push the piston     > back manually).     >     >     >The Slave Cylinder Repair Kit     >-----------------------------     >     >The slave cylinder repair kit contains     >     > - a boot for the push rod     >     > - a main seal for the piston     >     > - a cap for the bleeding valve     >     >     >     >Repairing the Clutch Slave Cylinder     >-----------------------------------     >     >1. Place the slave cylinder in a vise, bleeding valve down. As you can     > see now, the piston is retained by a circular clip sitting in a grove     > in the slave cylinder. However, that's not the regular C-clip you     > can remove with the corresponding pliers. Rather use a small screw     > driver and a hammer and drive the screw driver between circlip and     > slave cylinder at the side oposite the gap in the circlip, at the     > same time pushing the piston slightly back with one finger of the     > hand holding the screw driver. This will push one side of the     > circlip down while the other end will go up allowing you now to     > easily remove the circlip.     >     >2. Next push the piston down the slave cylinder, close the opening for     > the hydraulic fitting with your thumb, and then suddenly remove the     > thumb so the piston will shoot up and half way out of the slave     > cylinder, where you now can easily pull it out altogether. Remove     > the spring from the rear end of the piston and then remove the old     > seal by simply using a srew driver and pulling the seal over the rear     > end of the piston (it's elastic enough).     >     >3. Dry the piston as well as the inside of the slave cylinder and then     > use finest emery-cloth to remove any residues from both, cylinder and     > piston.     >     >4. Next, pull the new seal over the rear end of the piston. Mind that     > the upper and lower edges of the seal have different outer diameters.     > The greater outer diameter points to the rear end of the piston,     > where the spring is attached. Put spring and piston back into the     > slave cylinder, push the piston down a little, and insert the     > circlip.     >     >5. Now turn the slave cylinder in the vise upside down, so that the     > bleeding valve is pointing upwards. Again apply some WD40, then use     > a 7mm wrench to screw the valve entirely out of the slave cylinder.     > Clean the valve, in particular the little hole near the pointed end,     > then reassemble the valve and close it tightly.     >     >     >Installing the Clutch Slave Cylinder     >------------------------------------     >     >Basically undo all the steps you did before to remove the slave cylinder     >in reverse order. However, mind a few things:     >     > - Put one of the copper washers on the hydraulic bolt, then the     > hydraulic eye, then the other copper washer. Then screw the     > hydraulic fitting into the slave cylinder. To tighten the bolt,     > again form a flat triangle with the slave cylinder and a 17mm box     > wrench. This time, however, the box wrench is at the left side,     > the slave cylinder at the right, and the head of the hydraulic bolt     > is again facing you. The rubber boot should not yet be installed.     > Before you fasten the bolt by placing this triangle on a piece of     > wood and striking the eye of the wrench more or less gently with a     > hammer, make sure the orientaion of the hydraulic hose is roughly     > perpendicular to the slave cylinder and downward.     >     > - Top off the brake fluid reservoir in the instrument cluster and     > bleed the system. The bleeding valve is easily accessible now with     > the slave cylinder just hanging below the tranny, and you can also     > easily check for any leaks (if the slave cylinder is leaking at the     > hydraulic fitting you probably forgot to insert one of the two     > copper washers).     >     > - Install the rubber boot (but not yet the push rod) at the lower end     > of the slave cylinder and -- folding the rubber boot against the     > slave cylinder -- persuade the slave cylinder to go up above its     > mounting bracket again. Insert the rear bolt from below and screw     > on the nut a few turns only. Then insert the push rod between the     > clutch operating lever and the slave cylinder piston, press the     > slave cylinder down against its mounting bracket, insert the front     > bolt with its shaft pointing up, and screw on the nut. Fasten the     > front bolt from below using a 13mm socket on a long extension and a     > 13mm wrench to fix the bolt, then fasten the rear bolt from the     > engine bay using two 13mm wrenches. Place the rubber cap on the     > bleeding valve.     >     > - Pull the lower end of the rubber boot down the push rod until it     > sits in the small grove at the lower end of the rod. Attach the     > two clamps to the frame that are holding the flexible clutch hose.     >     > - Test the operation of the clutch: pull parking brake, put the     > tranny into first gear, step on both, the brake and the clutch     > pedal, and then start the engine.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.