Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (April 2009, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 12 Apr 2009 13:42:55 -0700
Reply-To:     Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject:      Re: Trying To Understand Tie rod Adjustments
Comments: To: Tom Hargrave <thargrav@HIWAAY.NET>
Content-Type: text/plain; format=flowed; charset="windows-1250";
              reply-type=original

care to wager ?

----- Original Message ----- From: "Tom Hargrave" <thargrav@HIWAAY.NET> To: <vanagon@GERRY.VANAGON.COM> Sent: Sunday, April 12, 2009 1:22 PM Subject: Re: Trying To Understand Tie rod Adjustments

> Scott, > > I understand - I've done enough backyard alignments. I'd never do one for > real road use - it's just not possible to get close enough. > > Thanks, > Tom Hargrave > www.kegkits.com > http://www.kegkits.com/JABF/ > 256-656-1924 > > > -----Original Message----- > From: Scott Daniel - Turbovans [mailto:scottdaniel@turbovans.com] > Sent: Sunday, April 12, 2009 3:17 PM > To: Tom Hargrave; vanagon@GERRY.VANAGON.COM > Subject: Re: Trying To Understand Tie rod Adjustments > > right........ > but we're not talking about 'on a rack at the alignment shop' are we ? > > We're talking about back yard............shade trees mechanicin' > ............... > > and........I'm curious - is Neil's goal to get it good enough to drive to > an > > alignment shop, > or get it good enough for real road use ? > I get them quite good with just back yard methods. .. > and ................( on no ! ) no centerline reference point. > > ok.......trivia question....... > name a mass-produced four door hatchback car from a Euupean car company > ..... > with a wheel base that is shorter by a solid 3 inches or so on the right > side, than on the left side . > ( and if you tweak the torsion bar preloads incorrectly......you can get > oversteer turning one direction, > and understeer turning the other direction - lots of fun ) . > > Scott > > ----- Original Message ----- > From: "Tom Hargrave" <thargrav@hiwaay.net> > To: "'Scott Daniel - Turbovans'" <scottdaniel@TURBOVANS.COM>; > <vanagon@GERRY.VANAGON.COM> > Sent: Sunday, April 12, 2009 1:06 PM > Subject: RE: Trying To Understand Tie rod Adjustments > > >> Actually, there is a center line, or more correctly, a center plane - it >> is >> calculated by the machine when the car is put on the alignment rack. >> Consider the center plane a vertical wall that goes straight through the >> vehicle from front to back and it is at a perfect right angle to the >> rack. >> >> All alignment measurements are referencing this center plane. >> >> Thanks, >> Tom Hargrave >> www.kegkits.com >> http://www.kegkits.com/JABF/ >> 256-656-1924 >> >> >> -----Original Message----- >> From: Vanagon Mailing List [mailto:vanagon@GERRY.VANAGON.COM] On Behalf >> Of >> Scott Daniel - Turbovans >> Sent: Sunday, April 12, 2009 2:42 PM >> To: vanagon@GERRY.VANAGON.COM >> Subject: Re: Trying To Understand Tie rod Adjustments >> >> all right ....... >> I'm getting what's going on perhaps ....... >> Neil for your thinking ........IF there was a 'center line' in the middle >> of >> the van , that you measured toe from for each front wheel....... >> that would make perfect sense......but there isn't. >> >> the 'physical point' you measure from is .........each front wheel >> relative >> to the other. >> you measure between the front and rear edges to get the toe reading. >> ( which is why I wrote that 'it balances out' ...........like if you >> start >> out with the left wheel at zero toe, and the right one toed out say a >> half >> inch .........as soon as you drive 6 feet.........they'll balance out ( >> and >> the steering wheel will move left some in this case ) ........ >> so you'll be driving down the road.........going straight, and with a >> half >> inch of toe out , measured from wheel to wheel in front. >> >> here's how I measure toe...... >> suspension must be settled of course. >> using two yard sticks..........measure the distance between the two front >> wheels.........as close to the 3 o'clock and 9 o'clock positions as you >> can >> get. >> I measure on the tire itself...........on a smooth spot , like no letters >> or >> bumps. >> Measuring on the wheel rim is OK.........but, the further you get from >> the >> center of the wheel, the more accurate your measurements will be. >> >> supposing you had a 10 foot long 2 X 4 mounted on each spindle perfectly >> .....so that they extended 5 feet for and aft from each spindle. >> then you measure toe by comparing the distance between the two ends of >> the > >> 2 >> X 4's way out in front...... >> then at the rear of the 2 X 4's .......this of course would be far more >> accurate, since the 2 X 4's magnify things. >> >> but that's not too practical. >> I just measure at the tires.......from side to side..........at the front >> of >> the tires, and at the rear...... >> aiming for about 1/16ths to 1/8th inch toe in, measured at the tires. >> >> hope this helps some !~ >> Scott >> www.turbovans.com >> ----- Original Message ----- >> From: "neil N" <musomuso@gmail.com> >> To: "Scott Daniel - Turbovans" <scottdaniel@turbovans.com> >> Cc: <vanagon@gerry.vanagon.com> >> Sent: Saturday, April 11, 2009 11:29 PM >> Subject: Re: Trying To Understand Tie rod Adjustments >> >> >>> 2009/4/11 Scott Daniel - Turbovans <scottdaniel@turbovans.com>: >>>> I meant to also say ..... >>>> for a base steering wheel being centered place to start - >>>> remove the key, and let the steering lock with the steering wheel >>>> centered. >>>> then try to get toe and camber right , >>>> and i ... >>> >>> >>> Thanks Tom and Scott. >>> >>> I'm starting to understand more. And I was right in thinking that a >>> wheel could be toed in or out independantly of the other. So with that >>> in mind.... >>> >>> A point of confusion remains. (and this may not be the problem, but I >>> suspect it is due to swap of a tie rod) >>> >>> Let's way the left wheel is 0 toe, but the right wheel is x degrees >>> toe out. How do I get the right wheel to 0 so I can set the correct >>> amount of toe in? i.e. what physical point do I measure from to set >>> the toed out wheel straight? >>> >>> Neil. >>> >>> >>> >>> -- >>> Neil Nicholson '81 VanaJetta 2.0 "Jaco" >>> >>> http://tubaneil.googlepages.com/ >>> >>> >> > http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engine >> s >> >> No virus found in this incoming message. >> Checked by AVG. >> Version: 7.5.557 / Virus Database: 270.11.53/2054 - Release Date: >> 4/11/2009 >> 10:51 AM >> >> >> No virus found in this outgoing message. >> Checked by AVG. >> Version: 7.5.557 / Virus Database: 270.11.53/2054 - Release Date: >> 4/11/2009 >> 10:51 AM >> >> > > No virus found in this incoming message. > Checked by AVG. > Version: 7.5.557 / Virus Database: 270.11.53/2054 - Release Date: > 4/11/2009 > 10:51 AM > > > No virus found in this outgoing message. > Checked by AVG. > Version: 7.5.557 / Virus Database: 270.11.53/2054 - Release Date: > 4/11/2009 > 10:51 AM


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.