Date: Sun, 24 May 2009 11:49:31 -0700
Reply-To: Robert Fisher <refisher@MCHSI.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Robert Fisher <refisher@MCHSI.COM>
Subject: Re: Electrical question (non-starting)
In-Reply-To: <c2c43a7e0905241107r61812217mc1d942e29b115596@mail.gmail.com>
Content-Type: text/plain; charset="iso-8859-1"
Thanks for the reminder; I did check all that, cleaned the ground and so
forth. I've been through starter failure before on this van and it turned
out to be the ground, so I was thinking of those things when I did the R &
R. I don't think I mentioned it (or more like I found this out after I
posted), but I got my headlights back as well after I pulled and replaced
the 'B' and 'D' connectors off the back of the fuse panel. I noticed on the
'D' plug that one of the wires had some scorching around the connector. I
also have the thing where the turn signals don't work but the indicator bulb
in the dash is lit up.
It's been in the back of my mind to clean those ground clusters under the
dash and localize the headlight grounds so I'm going to go ahead and do that
in the case that I have a general ground issue. We'll see how it goes.
Cya,
Robert
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
Marc Perdue
Sent: Sunday, May 24, 2009 11:07 AM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: Electrical question (non-starting)
Robert,
I was starting to go through all this complicated measurement stuff
and replacing switches and all when my van wouldn't start. It turned
out that the red wire connecting to the starter had a loose
connection. Since you just did some work in this area with the
transmission, it might be worth looking at . . . Way easier to take a
pair of needlenose pliers and tighten that connector than to go
replacing switches and taking measurements all over . . . Cheap too!
:^)
Marc
On Sat, May 23, 2009 at 9:09 PM, Robert Fisher <refisher@mchsi.com> wrote:
> Thanks for the info. I didn't get to the pin/current check; I pulled the
> connectors out of the panel and checked the wires visually and with a
meter,
> plugged them back in and it started, tho grudgingly. In a way I'm not
> surprised. I had to jiggle the key a bit but it starts.
> Since both ignition switches are over 20 years old I'm going to get
> replacements. I have a number of other things to do while waiting for
parts
> so I'm going to leave the panel down and check everything as you suggested
> with the new switch in.
> Guess I need to study up on reading those wiring diagrams as well.
>
> Cya,
> Robert
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
> David Beierl
> Sent: Friday, May 22, 2009 7:11 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Re: Electrical question (non-starting)
>
> At 09:00 PM 5/22/2009, Robert Fisher wrote:
>>Voltage at the red wire into the ignition switch is equal to the battery
at
>>around 12.2 (I know it's low, I've been messing with this for a few days
> now
>>and I need to charge it); when I turn the switch, the outbound voltage is
>>about 10.2 and it drops to about 8.4 at the neutral safety switch. I can't
>>make much out of the diagrams in the Bentley but it seems to me that the
>>line between the ignition switch and the safety switch is one wire.
>
> According to 97.147 the wire from the ign sw 50 terminal goes to
> terminal B8 in the panel, then comes out D24 and goes to the 50
> terminal on the safety switch. So you've got four wire-end terminals
> to check, plus the contact where the two plugs mate with the panel.
>
> Measure from point to point on the wire and you'll find where the
> high-resistance joint(s) are -- that's where your missing voltage
> will show up. Use a pin or needle to pierce the insulation to test
> where the terminals crimp onto the wires...
>
> Incidentally -- 97.4-5 tells you how to read the diagrams.
>
>
> --
> David Beierl - Providence RI USA -- http://pws.prserv.net/synergy/Vanagon/
> '89 Po' White Star "Scamp"
>
|