Date: Wed, 22 Jul 2009 18:22:58 -0700
Reply-To: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject: Re: Door Chime madness
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
was gonna say the same thing.
just pul that sucker out of there.
I want to leave the key in while I work on it etc...
don't want to hear that thing ever.
That 'should' fix it, although .........the 'leakage' making it sound
faitly, is of concern. Makes me wonder if all electricity is finding it's
way cleanly to the consuming devices, and they are getting their full shot
of power cleanly. In other words, resistance to devices is minimal, and
grounds are good.
in an ideal cirucit all the voltage drop of the circuit occures in the
consuming device , and switches and wires leading to it transfer full power
to the device, and don't use up any power themselves. Same is true for the
ground side and connections .............that's not supposed to use up any
voltage either.
The total volatage drop in the circuit will be equal to the voltage
availale.
We want the majority of the total voltage drop to occur in the device, not
in wires, switches or conenctions.
If the resistance of those is high..........part of the voltge drop will
occur in those poor connections or old wires, and not as much in the device.
Say the circuit has 12.8 volts..
we'd love to see say, the device getting and using up 12.6 volts, and the
rest of the circuit .2 volts,
it's possible for resistance elsewhere in the circuit to be say ..........3
volts total, so then the device only gets 9.8 volts ( of 12.8 total
available ) .
your comment about 'faintly chiming' made me think there is voltage
not going where it should, or not going where it's not suppossed to go.
If any electrical guru's want to correct my 'total voltage' drop in the
circuit words , fire away.
It's also fun to measure voltge drop across a ground connection.
I think I read that max alloable is about 300 millivolts, or .3 volts.
If more voltage is dropped by a ground point than that, resistance has built
up there.
you mearsure this by energizing the circuit, then putting the probes of a
DVOM on both sides of the ground point ........and see what voltage you see
dropping across that ground point, 'Zero' would be ideal. 300 milivolts it
the upper acceptable range,
----- Original Message -----
From: "Jake de Villiers" <crescentbeachguitar@GMAIL.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Wednesday, July 22, 2009 6:03 PM
Subject: Re: Door Chime madness
>I always simply pull the chime/buzzer/bell relay when I get a new car - if
>I
> open the door in a quiet spot I don't need that stuff happening! =) Its
> just plugged in to your relay panel.
>
> On Wed, Jul 22, 2009 at 5:34 PM, Troy <colorworks@gci.net> wrote:
>
>> It's amazing how little electrical problems can make you think your
>> vehicle
>> is possessed. My door chime has been working intermittently over the last
>> month or so and suddenly decided to work all the time, but here's the
>> mystery. Even when the door is closed the chime is still working,
>> however,
>> the volume is extremely faint. I thought I was hearing things at first it
>> is
>> so low. Presumably there is a very low phantom voltage happening? I did
>> replace the ignition switch a few months ago, no issues since (or before
>> really) and recently popped the cover off the fuse box, and perhaps I
>> disturbed something. Before I start ripping the dash apart, any ideas of
>> what is going on? I assume that since the volume is dimmed, there is
>> still a
>> area small amount of voltage going through the circuit. I also noticed
>> after
>> several days, voltage has gone from 12.7 down to 12.3, so there is
>> definitely a drain. I hate troubleshooting electrical! Could somebody
>> give
>> me the basic steps to troubleshoot this circuit? I think there is a gray
>> and
>> white wire going to the switch but I cannot remember, with the actual
>> chime
>> somewhere on the left top of the dash. I definitely need to track this
>> down
>> or it's going to drain my battery dry. Any help appreciated.
>>
>> Troy
>
>
>
>
> --
> Beverley Anne de Villiers April 20, 1930 - July 4, 2009
>
> Jake
>
> 1984 Vanagon GL
> 1986 Westy Weekender "Dixie"
>
> Crescent Beach, BC
>
> www.thebassspa.com
> www.crescentbeachguitar.com
> http://subyjake.googlepages.com/mydixiedarlin%27
|