Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (August 2009, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Wed, 19 Aug 2009 14:16:15 -0700
Reply-To:     Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject:      Re: Fox head torque question
Comments: To: roger sisler <rogersisler2000@YAHOO.COM>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
              reply-type=original

I suppose you could just see if the head bolts have say, at least 80 lbs torque on them. Not 'too' valid a test, but you just want to make sure they are tight I beleive.

They are stretch head bolts of course. I beleive that after that intial 44 lbs plus 1/2 turn, .......you do another have turn after it's warmed up ( after putting a fresh head gasket, and new bolts on ) .....and then maybe even another half turn after 1,000 miles.

those 'half turns' are scary sometimes, as it feels like you are twisting the bolts at 200 ft. lbs......like I'm afraid they'll break off, those half turns take so much force to do. also....... the head gasket gets more stress on it than any part in the engine, endless warm up cool down cycles, the heat of combustion etc. It's amazing how well they do last. It's completely normal for any used VW engine, to need a new head gasket, more or less - 'specially a high miles engine. I like good german aftermarket head gaskets, no Felrpo's or other 'melican stuf.. New stretch head bolts too of course. They're not expensive.

Scott www.turbovans.com

----- Original Message ----- From: "roger sisler" <rogersisler2000@YAHOO.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Wednesday, August 19, 2009 1:12 PM Subject: Fox head torque question

Hello, this 1.8 is similar to many VW inline four engines, and it is loosing coolant at the rate of about 1 qt per 50 miles. No exterlal leaks are to be found, therefore I think it is a head gasket issue. This Fox had been leaking coolant for some time(damn VW's), however I traced it to a lose coolant temp sensor at the bottom of the radiator.Got that fixed, and then this thing started eating up all my antifreeze.

I first want to check the torque on the head gasket to see if all the bolts are tight to specs. I see that the spec is 44ftpounds + 1/2 turn. That seems like a difficult measurement to tell if a bolt is loose.I mean. Does anyone know if there is a proper torque number for this cylinder head torque on the Fox?

thanks!


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.