Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (October 2009, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Mon, 26 Oct 2009 13:06:13 -0400
Reply-To:   Robert Stewart <robertmstewart@MAC.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Robert Stewart <robertmstewart@MAC.COM>
Subject:   Think I have sprung a leak in my powersteering lines! Need some guidance please.
Content-Type:   text/plain; charset=US-ASCII; format=flowed; delsp=yes

Hi everyone,

I need some guidance please.

I have a 2.1L Automatic 1988 Wolfsburg. Just rebuilt the engine and had all new hoses put on.

Prior to the install the power steering pump had a minor leak, now after the rebuild no leak.

2 days ago in pouring rain I noticed the steering was very stiff. So I looked at the ATF fluid in the Power Steering Tank. It was almost empty so I filled it.

10 minutes later it was making noise when trying to turn at slow speeds pulling from the parking lot. So I filled again with some Lucas Stop leak and topped it off with some more ATF.

Got home and it was empty. So I look today to see if I can see anything. I had the lines replaced the fat & thin lines with copper ones in 2007 I believe. I am noticing some red fluid around some areas of the lines but I can't be sure where its really coming from.

Where are the key areas to look for leaks?

Will it kill my pump if I drive it with some fluid in it that drains out over the time of me driving it to get it fixed?

I assume the best thing to do is just replace them with Hydraulic lines?

Walrus from the Samba posted some details on having them custom made but I need someone to confirm his data please. He stated they should run around $40.

I assume I need to go to hydraulic shop or tractor shop to get them made?

Walrus's instructions for building 2 Power Steering lines: http://www.thesamba.com/vw/forum/viewtopic.php?t=147368&highlight=steering+fluid+leak

High Press line 11.5' long, two female compression fittings, 16x1.5mm Needs to be flex industrial stainless braided rated 4200lb. I.D. is 5/16". I believe I used 3/8". Connects where metal line junctions with the 1.5' section of hose held onto pump with banjo bolt.

Low Press line 13' long, Needs to be rated 400lb? 1/2" I believe. Connects from Reservoir to rack. I cut the pipe 4 inches from rack and connected by sliding hose over pipe and used hose clamps. Other end hose clamps to reservoir.

Is this an easy job for one person to do in their backyard? How long should it take?

If I brought the lines to a mechanic with a lift how long should it take to replace the lines and add the fluid?

Do the lines need to be bled out or anything? A special process for testing it and making sure its installed properly?

Thanks, Robert NY


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.