Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (December 2009, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 7 Dec 2009 16:10:11 -0500
Reply-To:     Mark <mbrush@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mark <mbrush@GMAIL.COM>
Subject:      Re: e-brake boot (the underside)
Comments: To: Dennis Haynes <d23haynes57@hotmail.com>
In-Reply-To:  <BAY132-DS6871F3E82B8881E100F9EA0900@phx.gbl>
Content-Type: text/plain; charset=ISO-8859-1

All good points. I need to move the tube into the correct place.

If I disconnect the e-brake at the lever (from inside the van), I wonder if I can pull it back and then thread it back in place so it's UNDER the crossover tube. I'm not sure I have enough play to do that. It looks like it's part rod and part cable before it makes the bend under the van.

The other option is to disconnect one side of the crossover tube. This may be the easiest solution. Undo the right side of the tube (passenger side), rethread, then reattach. I'm not sure, but I think I can do all that through the wheel well.

On Sun, Dec 6, 2009 at 10:54 PM, Dennis Haynes <d23haynes57@hotmail.com>wrote:

> That e-brake cable can have a pretty good whipping effect to it. The cross > over tube when properly installed is actually held up to the body by a clip > and sheet metal screw. The tanks then get raised into position and the tube > ends get pushed into the tank grommets after the tank is almost up. Yes, > you > reach into the are above the tank with your hands and connect the ends. The > plastic sleeve trick may work for a while but I have found it is easier to > replace that front brake cable by dropping the tank slightly. You need some > extra room to get that guide block down and back in. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of > Mark > Sent: Sunday, December 06, 2009 10:15 PM > To: vanagon@GERRY.VANAGON.COM > Subject: e-brake boot (the underside) > > I searched the archives for some advice but didn't come up with much. I > need to get access to the e-brake cable - the part that's right above the > front of the gas tank. My problem is that the cable is rubbing my > crossover > tube on the gas tank (I threaded the tube incorrectly and I'm don't want to > drop the tank again). I want to slip a plastic sleeve over the cable so it > won't rub a hole through the tube. > > So my question is... from the inside of the van... can I pull up the carpet > and remove the boot - the boot on the underside of the vehicle - once I > unhook the cable from the lever. If I can, I can slip my plastic sleeve on > and reassemble everything (in theory). > > -- > Mark > 1990 Westy (2.1 - manual) > >

-- Mark 1990 Westy (2.1 - manual)


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.