Date: Thu, 11 Feb 2010 23:15:50 -0500
Reply-To: pdooley <psdooley@VERIZON.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: pdooley <psdooley@VERIZON.NET>
Subject: Re: TIICO/ABA engine question
In-Reply-To: <71d9cdf91002111929k7ad1a5fav11f6f7069b940edb@mail.gmail.com>
Content-type: text/plain; charset=US-ASCII
The ABA has oil jets from the factory.
And the design load of the ABA bottom end has a factor of safety of at least
2-2.5.
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
Jake de Villiers
Sent: Thursday, February 11, 2010 10:29 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: TIICO/ABA engine question
Nope. You might try one of the Rabbit/Golf hop-up sites.
VW paid really good engineers a ton of money to maximise the output of that
motor. Don't you think that if another 25 ft/lbs was right there they would
have done it? That's where most folks want their power, off the line, not up
at 6500 RPM.
Aftermarket cams always move the torque peak higher, thus adding horsepower
(HP = torque x RPM/5252) but at the expense of flexibility.
If you want more bottom end you'll need to add displacement - you could do
that with a supercharger I guess, but then you'd be exceeding the design
loads on the wrist pin bushings and rod bearings.
Go ahead and add oil jets to cool the pistons, an external oil cooler to
cool the oil and an engine compartment fan to keep temps down.
Having raced cars for a while, I went through that circle quite a few
times...its challenging and fun, if time-consuming and expensive, and these
days I prefer my street cars to be a little easier to drive!@ =)
On Thu, Feb 11, 2010 at 6:50 PM, Chris S <szpejankowski@gmail.com> wrote:
> Jake, anything to add about the subject line?
>
> 2010/2/11 Jake de Villiers <crescentbeachguitar@gmail.com>
>
>> Subaru 2.5 has 165 ft. lbs of torque right off idle and 165 hp up top -
no
>>
>> nasty turbo required! =)
>>
>> On Thu, Feb 11, 2010 at 8:36 AM, David Marshall
>> <mailinglist@fastforward.ca>wrote:
>>
>> > The ABA cam is already optimized for lower end power. Even the cams
>> > from the 1.8L arn't as nice as the ABA for the low end. No idea what
>> > the RemTec motor is setup for.
>> >
>> > You have 122 ft.lbs of
>> > toque which really isn't much to write home about compared to the wbx
>> 117
>> > - only way to get much more torque is getting a turbo engine, a little
>> > more torque would come from chip tuning.
>> >
>> > David Marshall
>> > VW
>> > Adventure Driver and BMW Adventure Rider
>> >
>> > HasenWerk
>> > http://www.hasenwerk.ca
>> >
>> > On Thu, February 11, 2010 08:20,
>> > Chris S wrote:
>> > > Folks,
>> > >
>> > > Does anyone know how
>> > the TIICO camshaft compare the ABA cam? Does anyone
>> > > have the
>> > specs, like lift, duration etc?
>> > >
>> > > I'm trying to analyze
>> > ways to increase torque and bottom end power of the
>> > > ABA.
>> > >
>> > > --
>> > > Chris S.
>> > > Disclaimer: "Death
>> > and serious injury may occur"
>> > >
>> >
>>
>>
>>
>> --
>> Jake
>>
>> 1984 Vanagon GL
>> 1986 Westy Weekender "Dixie"
>>
>> Crescent Beach, BC
>>
>> www.thebassspa.com
>> www.crescentbeachguitar.com
>> http://subyjake.googlepages.com/mydixiedarlin%27
>>
>
>
>
> --
> Chris S.
> Disclaimer: "Death and serious injury may occur"
>
>
>
--
Jake
1984 Vanagon GL
1986 Westy Weekender "Dixie"
Crescent Beach, BC
www.thebassspa.com
www.crescentbeachguitar.com
http://subyjake.googlepages.com/mydixiedarlin%27