Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (February 2010, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 11 Feb 2010 21:52:46 -0500
Reply-To:     Chris S <szpejankowski@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Chris S <szpejankowski@GMAIL.COM>
Subject:      Re: Cip1.com - wheels 5x112mm
Comments: To: Jake de Villiers <crescentbeachguitar@gmail.com>
In-Reply-To:  <71d9cdf91002111635j4bae10ase6a7c1cfc5154cb1@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

Agreed. Mercedes CLK forged wheels saved me 6lb per wheel/tire combo over stock steel wheels and ride like a dream.

2010/2/11 Jake de Villiers <crescentbeachguitar@gmail.com>

> The ET is definitely all wrong but European or Chinese, I still don't see > the point. Those wheels are mostly too narrow to be worth the trouble. > > Once you've tried 16 x 7 wheels on a Vanagon, there's no going back! =) > > On Thu, Feb 11, 2010 at 8:30 AM, Jason <uberhare@gmail.com> wrote: > > > Don't kid yourself. Even if they come from Europe, they may still be > > Chinese. There are many traders passing stuff off as their own. > > > > Jay > > > > > > On Thu, Feb 11, 2010 at 11:17 AM, Chris S <szpejankowski@gmail.com> > wrote: > > > > > Some of these are imported from Europe. > > > > > > They do look nice and some of them would look pretty good on an older > > > Vanagon. However, there's a small problem. Look at the back spacing: > > > http://www2.cip1.com/ProductDetails.asp?ProductCode=ACC-C10-6628 > > > > > > 5.5 inch wide wheel with 3.25 inch back spacing means an ET of 13. > Stock > > > alloys have an ET of 30, which means these will protrude 17mm further > > out. > > > You should try and stick to stock ET as close as possible to maintain > > > steering geometry of the front suspension and minimize stresses on the > > > wheel > > > bearings. If you read the fine print at the bottom of the wheel > > > description > > > they actually recommend machining them to increase ET. > > > > > > > > > > > > 2010/2/9 Hector Zapata <hlzapata@gmail.com> > > > > > > > Some of you might find this interesting... > > > > > > > > http://www2.cip1.com/SearchResults.asp?Cat=1935 > > > > > > > > > > > > Héctor > > > > 1990 Carat 'Ursula' > > > > > > > > > > > > > > > > -- > > > Chris S. > > > Disclaimer: "Death and serious injury may occur" > > > > > > > > > -- > Jake > > 1984 Vanagon GL > 1986 Westy Weekender "Dixie" > > Crescent Beach, BC > > www.thebassspa.com > www.crescentbeachguitar.com > http://subyjake.googlepages.com/mydixiedarlin%27 >

-- Chris S. Disclaimer: "Death and serious injury may occur"


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.