Date: Sat, 20 Mar 2010 18:45:17 -0700
Reply-To: Shawn Wright <vwdiesels@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Shawn Wright <vwdiesels@GMAIL.COM>
Subject: Re: Trans. Install: Input shaft & clutch splines
In-Reply-To: <c4e7c5f91003201550l1d2f359bh1ab3f0d39df8741e@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1
Yup, btdt at least twice now, but I didn't know that forcing the
trans/engine together was another possible cause... I've also read that
uneven wear in the clutch lever forks can cause p/b failure, which leads to
input shaft seal failure, etc. Since then I've always replaced or at least
evened out the clutch lever forks.
But keep an eye on things, and it's possible to save the clutch from oil
contamination if you catch signs of oil leaking at the bottom of the b/h
soon enough. (you may also feel the clutch grabbing erratically).
Tomorrow I plan on pulling my dash, so we'll see how fun that is compared
with the trans swap... :-)
On Sat, Mar 20, 2010 at 3:50 PM, neil n <musomuso@gmail.com> wrote:
> On 3/20/10, Jim Arnott <jrasite@eoni.com> wrote:
> >
> > On Mar 20, 2010, at 1:46 PM, neil n wrote:
> >
> >>
> >> When installing the transmission, is it obvious if input shaft/clutch
> >> splines aren't lining up? Is it possible the transmission can be
> >> "forced" in even if splines misaligned?
> >>
> >> I'm not totally unfamiliar with VW transaxle remove/install, but
> >> tonight, it was a royal PAIN. (don't ask) Anyhow, when things finally
> >> lined up, and enough thread was showing on lower studs, I used lower
> >> nuts, then uppers, to bring the transmission and engine together. It
> >> all "felt" ok while doing this, but because I had to use the nuts, I'm
> >> asking the above. FWIW, I did jockey the crank back/forth to help make
> >> sure splines lined up.
> >
> > Well..... I don't want to be the bearer of bad tidings, but the last
> > time I used the nuts to mate a reluctant trans to the motor I ended up
> > replacing the gearbox the following summer.. The reluctance was due
> > to the pilot shaft bearing being turned to little bitty pieces. A
> > year and about 5,000 miles later the input shaft seal failed. That's
> > when I found the deeply scored input shaft. The good news was that I
> > just happened to have a 'spare' gearbox and motor waiting to go in so
> > down time was minimal. But without waiting spares it would have been a
> > real 'Aw s....'
> >
> > I don't think that I'll "pull" them together again. Start your search
> > for an input shaft or gearbox just in case.
> >
> > Jim
>
>
>
> Thanks much Jim.
>
> This is a tranny swap (input shaft too as it's shorter for Jetta
> engine) so a spare is no issue. Just added time, blood, sweat and
> cussing.
>
> Hopefully I haven't mashed the PB. Didn't think of that scenario. That
> would be a shame as I gather one other item that can suffer is the oil
> sling on clutch housing.
>
> Neil.
> --
> Neil Nicholson '81 VanaJetta 2.0 "Jaco"
>
> http://tubaneil.googlepages.com/
>
>
> http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines
>
|