Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2010, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 5 Apr 2010 12:36:31 -0700
Reply-To:     Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject:      Re: Clutch Cross Shaft Arm Wear. Abnormal? PICS
Comments: To: neil n <musomuso@GMAIL.COM>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
              reply-type=original

nice pics. the face of the arm where it pushes the TOB ...wear there is 'normal' all right ...as in 'fairly common, but not desired at all.'

I'd say it's from lack of lubing that spot. I use black moly grease on those points. I lube the heck out of the entire throwout mechaism ... like a dozen spots. I spray lube the crosshaft bushings until the cross shaft pivots with zero drag. And I especially lube the tips of the fork arms - what's in your pics. If it was clipped in there like it belongs .... it was installed correctly ...just likely not lubed.

I also lube the guide tube the TOB slides on. Notice the groove inside the TOB ...that's for grease I believe...I grease that spot well. I like metal guide tubes better than plastic ones too.

'techician error' is what I'd chaulk that wear up to. Lack of plan ole lube ! That surface starts out curved or rounded, not flat.

I get the strongest impression at times that some people somewhere do not understand that metal can not rub on metal, that they must be separated by a film of some good lubricant - in about 300 places in a vanagon .

----- Original Message ----- From: "neil n" <musomuso@GMAIL.COM> To: <vanagon@GERRY.VANAGON.COM> Sent: Monday, April 05, 2010 10:01 AM Subject: Clutch Cross Shaft Arm Wear. Abnormal? PICS

> Hi all. > > Transmission would catch slightly in all gears. Pulled it, and TOB > appeared to be installed incorrectly. It appeared loose. (at time, I > also suspected poor clutch hydraulics. He said hoping transmission is > ok! :) > > Are these wear points on each arm normal high mileage wear? If not, do > they indicate an incorrectly installed TOB? > > http://tinyurl.com/ykd8co9 > > http://tinyurl.com/yhyvdg8 > > Neil. > > > -- > Neil Nicholson '81 VanaJetta 2.0 "Jaco" > > http://tubaneil.googlepages.com/ > > http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.