Date: Mon, 3 May 2010 14:16:47 -0700
Reply-To: Roland <syncronicity1@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Roland <syncronicity1@GMAIL.COM>
Subject: Re: Found a timesert in the spark plug hole
In-Reply-To: <008d01caeb02$efa5c180$6401a8c0@PROSPERITY>
Content-Type: text/plain; charset=ISO-8859-1
Hi Scott, Tom, Mark,
Thanks for the additional insights.
When I wrote "square" I really did mean the "flat" seal, just didn't know
the terminology. Also, asked because the new plugs came with the washers,
and now I know that these are crush washers.
So, I am going to go for it.
- Anti-seize on the plug threads,
- screw the timesert onto the plug
- then put the thread locker on the outside threads of the insert. I'll use
the material that came with it, the package says it is for spark plug uses,
so I'll have to trust that it is valid for higher temperatures.
Then screw that combination in there, torque to the 22 ft. lbs that the
Bentley says. Let it sit overnight.
Only other alternative I thought of is to use one of the old spark plugs and
torque it to a higher value to maybe get a better seat on the insert. Then
wait a day, remove the old plug, and install the new one. Any views on this
idea? How much higher could I set the torque wrench if I used and old plug
first?
Sorry to be such a ninny on this one, just seems like a really dangerous
area where I could mess something up quite bad.
Thanks!
Roland
On Mon, May 3, 2010 at 1:54 PM, Scott Daniel - Turbovans <
scottdaniel@turbovans.com> wrote:
> exactly what Tom says here.
> It sure 'should be' what we're calling a square ( I'd call it flat ) seal,
> and uses a sealing washer ..
> that you just leave on the spark plug, where it should automatically be.
>
> driver's side rear is # 4 in any opposed four VW engine.
>
> as long as the insert doesn't come out with the spark plug, it should be
> fine.
> If there is a compression leak at the sealing surface where the plug screws
> into the head and insert...
> you should hear the leak with the engine running - listen there with a
> listening tube held to the ear.
>
> Scott
> www.turbovans.com
>
> ----- Original Message -----
> From: "Tom Hargrave" <thargrav@HIWAAY.NET>
> To: <vanagon@GERRY.VANAGON.COM>
> Sent: Monday, May 03, 2010 6:02 AM
> Subject: Re: Found a timesert in the spark plug hole
>
>
> Mark,
>>
>> 2 spark plug seal designs exist.
>>
>> The square seal is the one with the crush washer you have to make sure is
>> on
>> the plug before you install it.
>>
>> The taper seal has no crush washer. Instead the sealing surface on the
>> plug
>> and the head are tapered like a flare fitting.
>>
>> All the VWs I've owned had the square seal but I've not owned anything
>> with
>> the wasserbus engine yet.
>>
>> Tom
>> www.stir-plate.com
>>
>>
>> -----Original Message-----
>> From: Vanagon Mailing List [mailto:vanagon@GERRY.VANAGON.COM] On Behalf
>> Of
>> Mark Dearing
>> Sent: Monday, May 03, 2010 7:16 AM
>> To: vanagon@GERRY.VANAGON.COM
>> Subject: Re: Found a timesert in the spark plug hole
>>
>> In a message dated 5/2/2010 2:36:04 P.M. Eastern Daylight Time,
>> syncronicity1@GMAIL.COM writes:
>>
>> So a question, does the Vanagon spark plug hole have a tapered or square
>> seal at the top? Could this old "timesert" thing be the source of low
>> compression if it was incorrect? A couple of compression tests several
>> months ago showed this cylinder low (can't recall the number, the rear
>> one
>> on the driver's side).
>>
>>
>>
>> hello Roland there are a bunch of different plug inserts out there. They
>> all
>> work about the same. no compresion loss if installed correctly and head
>> has no cracks. hole is not tappered and I don't know what you are
>> calling
>> a square seal? Plugs do have sealing rings on them and should be left on
>> later mark d
>>
>
|