Date: Tue, 11 May 2010 19:06:40 -0500
Reply-To: tom ring <taring@TARING.ORG>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: tom ring <taring@TARING.ORG>
Organization: Tippen Ringware
Subject: Re: Good local mechanic worked on my 85
In-Reply-To: <12fa01caf145$8eac62a0$6401a8c0@PROSPERITY>
Content-type: text/plain; charset=US-ASCII
It's an 85 1.9 with about 104k on it.
Drove it 30 miles at freeway speeds, 60 to 72, today and it was running very
nice. I could hold about 68 just touching the second butterfly. Trying to
burn off about 3 gallons of 1 year old fuel mixed with fresh added up to
whatever the full tank holds. Going to add a can of Sea Foam before a run
after work tomorrow.
tom
K0TAR
On 11 May 2010 at 13:07, Scott Daniel - Turbovans wrote:
> it's not a matter of is proper backpressure needed,
> but more that exhaust vales will burn after a while with an exhaust leak
> near that exhaust port,
>
> I don't see which engine Tom the question asker has ...
> but I'll say that I find slightly burnt or rough exhaust valves on
> waterboxer 2.1's all the time.
> it's normal even ..
> I go to do head gaskets, check the valves for leakage, and the exhaust ones
> are usually a little leaky ..
> like doing 80 % of the sealing they should be doing.
>
> so given that, it's not that smart to run with significant exhaust system
> cracks or leaks.
> It could even be a fire hazard.
> in any engine.
>
> Scott
> www.turbovans.com
>
>
> ----- Original Message -----
> From: "tom ring" <taring@TARING.ORG>
> To: <vanagon@GERRY.VANAGON.COM>
> Sent: Monday, May 10, 2010 8:04 PM
> Subject: Re: Good local mechanic worked on my 85
>
>
> > And a question. I have had a very minor to major break in the exhaust for
> > a
> > few thousand miles. The very minor was a lengthwise split about 2 inches
> > from
> > the head and extending for about an inch and a half. That was around in
> > somewhat patched to not patched for a couple cycles for about 5 thousand
> > miles.
> > The major was the driver side forward cylinder. Broke at the flange. Bad
> > mojo. 20 miles home.
> >
> > Patched with the nasty white exhaust paste wrapped with the high temp buck
> > a
> > foot exhaust wrap and then with steel fence wire with about 1/16 to 1/8
> > spacing.
> >
> > Lasted for 150 miles, almost all I needed last summer.
> >
> > So the question - is proper/even back pressure a critical thing on these
> > engines? Because this thing is more balanced cylinderwise and just in
> > general
> > than I remember.
> >
> > tom
> > K0TAR
> >
> > On 10 May 2010 at 21:27, tom ring wrote:
> >
> >> Just had a local private mechanic install a new exhaust on an engine that
> >> had
> >> at least 1 broken stud. He removed and welded a couple other support
> >> bits
> >> during the job. Replaced the oxy sensor with new. Installed all new
> >> fuel
> >> lines and covered them with the old outside protective plastic shrouds.
> >>
> >> I supplied the new exhaust kit and fuel line kit but nothing else. He
> >> picked
> >> up the oxy sensor and replacement studs as well as a few other gaskets
> >> and
> >> bolts.
> >>
> >> Total bill - $330 including additional parts and shop. I like Westside
> >> VW, but
> >> this was a lot cheaper for 10 hours of work.
> >>
> >> He is in the Minneapolis metro if anyone is interested. Contact me at
> >> the
> >> shown email address.
> >>
> >> tom
> >> K0TAR
> >>
> >>
> >> __________ Information from ESET NOD32 Antivirus, version of virus
> >> signature database 5103 (20100510) __________
> >>
> >> The message was checked by ESET NOD32 Antivirus.
> >>
> >> http://www.eset.com
> >>
> >>
> >>
>
>
> __________ Information from ESET NOD32 Antivirus, version of virus signature database 5106 (20100511) __________
>
> The message was checked by ESET NOD32 Antivirus.
>
> http://www.eset.com
>
>
>
|