Date: Mon, 21 Jun 2010 19:38:01 -0700
Reply-To: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
Subject: Re: tire jack suggestions for 88 GL
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
re
"you never know how much the dudes in the
shop have cranked their air wrenches when putting your tires back
on................"
you let tires stores touch your van or install the wheels ?
I would never.
that's just asking for trouble.
I take my wheels and tires in another car, and have them do the mounting and
balancing,
then I put them on my van/s myself....it's the only way to know it's right.
speaking of needing a breaker bar ...
Road & Track had a fancy new volvo worked on at a dealership ..
including mounting wheels. And you might think they would do a good job for
a major nationally known magainze ( or maybe they didn't know )
anyway, they got a flat.
All the kings men, and all the kings horses could not get that wheel off.
Not the tow truck driver, not the CHP - nobody. It ended up costing them 500
bucks to get things straightened out. Wheel lug nuts were probably on at
500 ft lbs.
The only way to know it's really right is to do it yourself, sadly.
a good breaker bar, and 6 point socket helps, that's for sure.
----- Original Message -----
From: "Doug Alcock" <doug.alcock@GMAIL.COM>
To: <vanagon@GERRY.VANAGON.COM>
Sent: Monday, June 21, 2010 12:38 PM
Subject: Re: tire jack suggestions for 88 GL
> Breaker bar is the way to go. If you think about it the 4-way wrench has
> about half the leverage of the a breaker bar -- maybe less because of how
> far out from the lug it is. And you never know how much the dudes in the
> shop have cranked their air wrenches when putting your tires back
> on................I had a really bad experience with a 78 Westy and a flat
> tire I couldn't remove either with the stock wrench or a borrowed 4-way.
>
> Cheers,
> Doug
>
>
>
> On Sun, Jun 20, 2010 at 1:03 PM, Dave Mcneely <mcneely4@cox.net> wrote:
>
>> ---- Alistair Bell <albell@shaw.ca> wrote:
>> > well, as I mentioned before, there is a stock scissors jack available
>> > from bus depot.
>> >
>> > http://busdepot.com/details.jsp?partnumber=237011031
>> >
>> > but go ahead and adapt another jack :)
>>
>> Thanks Alistair. Now another question. I've never actually removed a
>> tire
>> and wheel from the van myself. I have, under the rear seat with the
>> jack,
>> an old fashioned four armed lug nut wrench. One socket on the wrench
>> fits
>> the lug nuts. But, should I have instead a breaker bar? And should I
>> use a
>> torque wrench to refit the lugs? What torque value? thanks, DMc
>> >
>> > alistair
>> >
>> >
>> >
>> > On 20-Jun-10, at 8:24 AM, Dave Mcneely wrote:
>> >
>> > When I first got the camper, I went through a drill to try out the
>> > OEM jack. I did not and do not like it, as it did not seem as stable
>> > as the scissors jacks that I have been accustomed to with Japanese
>> > vehicles. But, it worked, and I have not done anything about a
>> > better jack. One question I have, and have been a bit put off by in
>> > considering other jacks, is how does one adapt them to the jack
>> > points built into the side of the van? A scissors or a bottle jack
>> > either needs a notch or at least a flat place to fit the jack
>> > platform. How do you guys deal with that? I would like to have a
>> > jack that I trust more to remain stable while changing a flat if
>> > needed. Thanks, David McNeely
>> >
>>
>> --
>> David McNeely
>>
>
>
>
> --
> http://www.dougalcock.com
|