Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2010, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 18 Jun 2010 21:17:12 -0500
Reply-To:     Jim Felder <jim.felder@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Jim Felder <jim.felder@GMAIL.COM>
Subject:      Re: Tips on repairing chipped Vanagon grills
Comments: To: Richard Koerner <rjkinpb@SBCGLOBAL.NET>
In-Reply-To:  <630745.83179.qm@web83604.mail.sp1.yahoo.com>
Content-Type: text/plain; charset=us-ascii; format=flowed; delsp=yes

The epoxy will fill the spaces much better than bondo, in my opinion

Jim

On Jun 18, 2010, at 8:14 PM, Richard Koerner <rjkinpb@SBCGLOBAL.NET> wrote:

> I assume you guys use typical 5 minute epoxy glue, 2 part stuff, > available from any hardware store....is that right? I was going to > do the repair using the same technique but Bondo instead...wonder > which is going to be stronger? I have both on the shelf.... > > Rich > San Diego > > --- On Fri, 6/18/10, Jack R. <jack007@COMCAST.NET> wrote: > > From: Jack R. <jack007@COMCAST.NET> > Subject: Re: Tips on repairing chipped Vanagon grills > To: vanagon@GERRY.VANAGON.COM > Date: Friday, June 18, 2010, 6:08 PM > > Exactly how I did my grill!!!! Great tip, glad you shared it! > > Look at the results... bet you can't find the chip! > > this is the Original grill on my 84 Westy. > http://www.flickr.com/photos/77623993@N00/2634100682/sizes/l/in/photostream/ > > Jack R. > 84 Westy Wolfie > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On > Behalf Of > Jim Felder > Sent: Friday, June 18, 2010 8:38 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Tips on repairing chipped Vanagon grills > > When the thin plastic blades of your Vanagon's grill become chipped, > here's an easy way to make them look like new (requires respray). > > The method takes advantage that the adhesive side of clear, heavy duty > packing tape is also a good mold release for epoxy glue. Wherever you > have a chip, tape over it gently from the front with clear tape. The > tape will conform to the curve of the blades. Don't press too hard, > you want the tape to curve to the roll of the blade, front to back, > but also be even along the length of the blade so that the surface > looks even when you are done. > > Now turn the the grill face down and pour a dollop of epoxy behind > each taped spot. When it is cured, the tape will pull off of the grill > and also off of the epoxy. Take a wide file and file the filler > exactly flush with the front edge of the blade at each patch. Paint > satin black and you're done. > > I have done this in five spots to an old grill, and I would have to > take it off and turn it over to know where the repairs were made. > > Jim > No virus found in this incoming message. > Checked by AVG - www.avg.com > Version: 9.0.829 / Virus Database: 271.1.1/2946 - Release Date: > 06/18/10 > 14:35:00


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.