Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (June 2010, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 20 Jun 2010 10:22:40 -0700
Reply-To:     Jake de Villiers <crescentbeachguitar@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Jake de Villiers <crescentbeachguitar@GMAIL.COM>
Subject:      Re: tire jack suggestions for 88 GL
Comments: To: mcneely4@cox.net
In-Reply-To:  <AANLkTilvV3l1dHibs0emwPSSyjE3OdnVhOGk_Ca4NL97@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1

I meant to say that a 2 ton bottle jack is plenty strong - you're only lifting 1/4 of the vans weight.

Jake

On Sun, Jun 20, 2010 at 10:20 AM, Jake de Villiers < crescentbeachguitar@gmail.com> wrote:

> I jack from the lower control arms. Nice and flat and you only have to > lift a couple of inches, instead of cycling through the suspension travel > first...its way faster. > > Jake > > > On Sun, Jun 20, 2010 at 8:24 AM, Dave Mcneely <mcneely4@cox.net> wrote: > >> When I first got the camper, I went through a drill to try out the OEM >> jack. I did not and do not like it, as it did not seem as stable as the >> scissors jacks that I have been accustomed to with Japanese vehicles. But, >> it worked, and I have not done anything about a better jack. One question I >> have, and have been a bit put off by in considering other jacks, is how does >> one adapt them to the jack points built into the side of the van? A >> scissors or a bottle jack either needs a notch or at least a flat place to >> fit the jack platform. How do you guys deal with that? I would like to >> have a jack that I trust more to remain stable while changing a flat if >> needed. Thanks, David McNeely >> >> ---- Ryan Johnson <rhinoculips@GMAIL.COM> wrote: >> > Personally, I hate the OEM jack. When I was 30 miles up a rough and >> very >> > remote mountain road, I got a flat. The damn jack jammed half way up. >> It >> > wouldn't go up, nor down. It was high enough to get the flat off, but >> not >> > high enough to put the spare on. Thus, I had to chip and scratch away >> at >> > the hard and rocky road base with a folding shovel, hatchet and crow bar >> > until I had a deep enough hole to get the spare on. Then I had to pound >> the >> > jack out from under the van. A really pain in the arse. I am glad I >> didn't >> > have to dig a hole into the pavement to get my spare on........ >> > >> > Now I keep a hydraulic bottle jack and some short 2x6 boards and never >> > looked back. Its nice to pump up the jack and then twist the release >> valve >> > to lower. Much easier than winding a "hundred" times in both directions >> > with the OEM jack. My recommendation is to toss the OEM in the trash >> and >> > get a real jack. Ideally, I would go for a HighLift, but I have yet to >> find >> > a satisfactory place to keep it and it's a little overkill for the run >> of >> > the mill flat. >> > >> > Fair winds and following seas, >> > Ryan >> > >> > >> > >> > >> > On Sat, Jun 19, 2010 at 1:36 PM, David Beierl <dbeierl@attglobal.net> >> wrote: >> > >> > > At 10:27 AM 6/19/2010, Mike "Rocket J Squirrel" wrote: >> > > >> > >> Church. I destroyed my OEM jack by nit-wittedly leaning against the >> > >> rear of the van when it was up on the jack. Van was in neutral, >> > >> rolled a bit (it was on a slope) and twisted that jack like so much >> > >> licorice. >> > >> >> > > >> > > Cathedral. I'm too embarrassed to say what I did. It was long ago >> > > and I was a spavined wee thing of only forty or so. I'll say this, >> > > though -- the brake backing plate bent, and if you go to a certain >> > > parking lot in Seekonk MA you might still find the dent in the >> asphalt. >> > > Didn't hurt the jack or mount though, because they're both round and >> > > designed to spin. >> > > >> > > And it was three other guys, it never broke and it was that way when I >> got >> > > it. >> > > >> > > Yours, >> > > d >> > > >> >> -- >> David McNeely >> > > > > -- > Jake > > 1984 Vanagon GL 1.9 WBX 'The Grey Van' > 1986 Westy Weekender/2.5 SOHC Suby 'Dixie' > > Crescent Beach, BC > > www.thebassspa.com > www.crescentbeachguitar.com > http://subyjake.googlepages.com/mydixiedarlin%27 > >

-- Jake

1984 Vanagon GL 1.9 WBX 'The Grey Van' 1986 Westy Weekender/2.5 SOHC Suby 'Dixie'

Crescent Beach, BC

www.thebassspa.com www.crescentbeachguitar.com http://subyjake.googlepages.com/mydixiedarlin%27


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.