Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (June 2010, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 26 Jun 2010 11:21:24 -0400
Reply-To:     John Meeks <vanagon@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         John Meeks <vanagon@GMAIL.COM>
Subject:      Re: Pesky Oil Leak
Comments: To: Scott Daniel - Turbovans <scottdaniel@turbovans.com>
In-Reply-To:  <AANLkTinzLx7i2Sbvzbub_YujZWdPW4Ma37tec1jfB5ci@mail.gmail.com>
Content-Type: text/plain; charset=ISO-8859-1

The deed is done. I tapped the hole closed with a 1/8" flat head punch (thanks for that one Scott). This stopped the leak to the point where I could get it good and clean without a drip re-forming. Mixed the JB Weld and pressed it well into the hole area and surrounding grooves in the push rod tube.

It looks like it will stay. I couldn't get the tube to rotate though. That would have been an added leak stopper. I'll try Max's rescue tape if the JB looks iffy after it dries but it looks like the JB will hold.

Thanks for the great ideas!

John Meeks '91 Multivan Northern Michigan

Vanagon Rescue Squad www.vanagonauts.com

On Fri, Jun 25, 2010 at 10:26 PM, John Meeks <vanagon@gmail.com> wrote:

> Thanks for the good ideas. I was doubtful that JB would do the trick but > though I have some in my road kit, I've never had to use the stuff. Mike > S' suggestion to rotate the tube so the hole faces up is genius. So JB and > a 180 it is. I'll follow up with the results. > > John Meeks > '91 Multivan > Northern Michigan > > Vanagon Rescue Squad > www.vanagonauts.com > > > > On Fri, Jun 25, 2010 at 8:56 PM, Scott Daniel - Turbovans < > scottdaniel@turbovans.com> wrote: > >> two ways to repair that without moving the head. >> ( good sleuthing and photography btw ) >> >> one, is the expandable push rod tube. >> you remove rocker arm and pushrod, and rip out the bad push rod tube, >> then you compress the spring-loaded expandable push rod tube ...fit that >> in... >> and you've got a new push rod tube there. They can leak a tiny bit at the >> sliding junction.. >> but for repair use they're fine. >> >> the other one is epoxy steel.....JB Weld , etc. >> clean the spot real well, like with carb cleaner.. >> apply the goop , let cure. >> that can work well. >> >> Scott >> www.turbovans.com >> >> ----- Original Message ----- From: "John Meeks" <vanagon@GMAIL.COM> >> To: <vanagon@GERRY.VANAGON.COM> >> Sent: Friday, June 25, 2010 4:12 PM >> Subject: Pesky Oil Leak >> >> >> >> I'm no BP but I've been leaving 6" poodles if oil wherever I park. >>> I have tracked it's source to a tiny hole in the case side of a push rod >>> tube right >>> on the outside of one of those accordion ridges. >>> >>> http://picasaweb.google.com/vanagon/SaltbeltRustyParts#5486847990506798578 >>> >>> < >>> http://picasaweb.google.com/vanagon/SaltbeltRustyParts#5486847990506798578 >>> >I >>> don't want to pull the head to replace the tube so... Does anyone have >>> any >>> idea what >>> I could use to repair this ~3/32" hole >>> >>> John Meeks >>> '91 Multivan >>> Northern Michigan >>> >>> Vanagon Rescue Squad >>> www.vanagonauts.com >>> >> >> >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.