Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (July 2010, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Sat, 24 Jul 2010 21:19:19 -0400
Reply-To:   Mark <mbrush@GMAIL.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Mark <mbrush@GMAIL.COM>
Subject:   Re: stalling and hard restart
Comments:   To: Scott Daniel - Turbovans <scottdaniel@turbovans.com>
In-Reply-To:   <016001cb26e0$87139b50$6401a8c0@PROSPERITY>
Content-Type:   text/plain; charset=ISO-8859-1

Thanks for all your thoughts on this problem. Just reporting back to say it's been fixed. Turns out I had two bad relays (fuel pump relay and the ecu relay). Once both were replaced, the stalling and hard restart problem cleared up. 20 years is a long time for those relays to work - pretty impressive, actually. And I figured out why I was hearing what I thought was the fuel pump run continuously when I just replaced the fuel pump relay. It was actually engaging the idle stabilizer faster than my old relay, so I mistook the idle stabilizer buzzing for the fuel pump buzzing.

All cleared up now - on to the next thing (cleaning gunk under the luggage rack and putting little screens in the drain holes - that should be fun)

Mark

On Sun, Jul 18, 2010 at 9:20 PM, Scott Daniel - Turbovans < scottdaniel@turbovans.com> wrote:

> If you are 'sure' that the thing that keeps it from firing up is lack of > fuel pump running ... > you're on the right track with the fuel pump relay .. > though if your used one made the fp be on steadily ...that's sure not > right. > > IF ...it is simply a matter of fuel pump control...no parts like oxygen > sensor etc are involved.. > Listening for the fp to pre-run is a very good habit. I do that every time > I fire up any vanagon. > > there are only a few requirements to make that happen .. > power to the ecu, and ecu supplies ground to the fp relay to energize it, > to run the fuel pump. > power for the fuel pump comes from the main relay I believe ....consider > that part. > > if nothing else, at least to sort through the weirdness, I'd rig a manual > fuel pump switch temporarily .. > so that you can get 12 V to the fuel pump 'for sure' . > > if it's as simple as no power to the fuel pump ...that shouldn't be 'too > hard' to fix. > > if it's something else...say pump runs but there's not suffecient fuel > pressure, that's anohter story of course. I like to have a fuel pressure > guage on them while sorting through stuff like this. Currently I have on > between the front seats, but running fuel through the van like that is a bit > scary .. > and the engine cover doesn't close perfectly ....and heat gets in the > cabin, but by golly, I am sure there is fuel pressure on this one van with > an intermittant igntion problem. > > it would be nice to have another ecu. I have heard of one that would not > supply ground to energize the fuel pump relay, but only one. Usually they > are very good about that. > > if you are sure the pre-run feature is not working ....just work on that > and it shouldn't be that hard to track down. > once past the pre-run feature, , the next time the fuel pump runs is during > starter cranking .. > and ecu knows the engine is cranking due to seeing ignition .. > like if you take another distributor and plug it into your harness, turn on > your key, and turn that distributor with your fingers, you should hear the > fuel pump run then too. That's a nice test to do .. > shows that the entire fuel pump control circuit is working. When I see > fuel pressure also during that test, then I know that whole part of the > system is working like it should. > > seems to me that if the fuel pump won't pre-run, and it won't run during > cranking ... > and you are sure it's not pump or electrical connections for it ... > my mind goes to the two relays and the ecu. > > I believe in redundency for the sake of not getting stuck anywhere, and so > far I have not had to arrange a back up fuel pump power supply ........but I > sure would for any excuse . > As far as I am concerend they should have two complete redundant and > indepedent fuel pump power supplies, plus manual back up. > > the two relays are identical I think. > and it is amazing how many of these 20 year old relays work so reliably. > wouldn't be a waste of money to one or two high quality new ones in hand. > > I wouldn't dismiss the igntion switch either, even though it is new. > I just found one the other day .. > great starter cranking ...but no igntion during cranking. > > Scott > www.turbovans.com > > > > ----- Original Message ----- From: "Mark" <mbrush@GMAIL.COM> > To: <vanagon@GERRY.VANAGON.COM> > Sent: Sunday, July 18, 2010 5:54 PM > Subject: stalling and hard restart > > > > After new fuel tank, pump, filter, lines, ignition switch, temp II switch, >> a >> few ground wire clean ups, and an adjusted throttle switch - things are >> running MUCH better - BUT - I still have a problem. After driving for a >> bit, the bus will eventually stall and then have a really hard time >> restarting. Usually happens after I've driven it, get back in and I'm >> idling to leave a parking lot (STALLS). It's happened often enough that I >> can tell when it's NOT going to restart. The telltale sign is I don't >> hear >> the fuel pump engage for those brief seconds when I turn the key over >> (before I turn it all the way over). If I don't hear the fuel pump, when >> I >> turn it all the way over, it won't start. I keep retrying it until I hear >> the fuel pump cycle on. Once I hear that, the bus fires up. This >> happened >> with the old pump AND the new pump (though the new pump sounds a lot >> better >> when it cycles on - the old one seemed to struggle). >> >> It happened today, and I tried replacing the fuel pump relay with a spare >> I >> have. When I put that relay in, the fuel pump just cycled on continuously >> (not for the 3 or 4 seconds as normal). It didn't start. I put the old >> relay in - a few more tries - I heard the fuel pump cycle for a few secs - >> and it fired up and got me home. >> >> I know all the FI parts are interconnected, so it could be a bunch of >> things >> (O2 sensor, idle stabilizer, ECU??) - just wondering if this sounds >> familiar >> to anyone, or if anything comes to mind. >> >> Having fun learning how this machine works - but my machine is telling me >> that I have A LOT more to learn :-) >> >> Mark >> >> -- >> Mark >> 1990 Westy (2.1 - manual) >> > >

-- Mark 1990 Westy (2.1 - manual)


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.