Date: Fri, 27 Aug 2010 18:13:53 -0400
Reply-To: Mike <mbucchino@CHARTER.NET>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Mike <mbucchino@CHARTER.NET>
Subject: Re: 2.1 exhaust fastener question
In-Reply-To: <42cf.2d884f5a.39a8e5dd@aol.com>
Content-Type: text/plain; format=flowed; charset="iso-8859-1";
reply-type=original
Nylock nuts are inappropriate for use on high-temp assemblies. High-temp,
crimped-type locknuts are the right hardware for the this job. Nylon
plastic softens or melts at a fairly low temp, which defeats the entire
purpose of the locknut. I found stainless steel, high-grade, crimp-type
locknuts at Lowe's.
Also, 'too-long' bolts, stacks of washers (lock and/ or flat) is also
incorrect, especially for excessive exposed threads. This invites damaged
bolt end-threads due to exposure or corrosion, and will make subsequent
removal difficult to impossible.
ETKA shows factory lengths for my '87 Westy 2.1 exhaust bolts;
http://www.vagcat.com/epc/cat/vw/T2/1987/65/50/676378/
I spend time (and money!) getting the right parts and checking installed
lengths for these very reasons. If you care enough to do it right, do it
right the first time, and you'll be glad later that you did!
This workmanship habit comes from years as a licensed aircraft/ jet engine
mechanic, both civilian and military.
Mike B. TSGT, USAF-ret.
--------------------------------------------------
From: "Frank Condelli" <RAlanen@AOL.COM>
Sent: Friday, August 27, 2010 5:56 AM
To: <vanagon@GERRY.VANAGON.COM>
Subject: Re: 2.1 exhaust fastener question
> In a message dated 26/08/2010 2:12:50 P.M. Eastern Daylight Time,
> LISTSERV@GERRY.VANAGON.COM writes:
>
> Gregory, those spring washers are not needed. I have been fitting
> Vanagon Exhaust systems like for over 10 years and NEVER use them. A
> stainless steel bolt with stainless steel flat washer up against the hole
> that
> is slotted and a stainless steel nylock nut on the other end. This is
> the
> scenario for all joint connections in the exhaust systems I install and
> sell. They will not come loose if installed correctly. Please consider
> my
> _Vanagon Stainless Steel Exhaust Systems_ (ht
> tp://frankcondelli.com/exhaust.htm) in any of your future exhaust
> replacements.
>
>
>
>>>>>>I just replaced the "J" pipe on my '88 GL, the end at the manifold
> rusted out and it sounded like a tank. In fitting the new pipe, I'm
> wondering about the stack of 5 washers on each bolt at that end. I
> omitted them for now until I find out what is best to use. Are these
> just spring washers or something else? Can I use a spring like others
> do? The existing ones were pretty gone. Can I leave it without them?
> =20
>
> Secondly, I am considering a complete new exhaust minus this pipe and a
> muffler which is 1 year old. Any gotchas?=20<<<<<<<<<
>
>
>
>
>
> Cheers,
>
> Frank Condelli
> Almonte, Ontario, Canada
> '87 Westy & Lionel Trains (_Collection for sale_
> (http://frankcondelli.com/trainsal.htm) )
> _Frank Condelli & Associates_ (http://frankcondelli.com/busindex.html) -
> Vanagon/Vanagon Westfalia Service in the Ottawa Valley
> _Vanagon Stainless Steel Exhaust Systems_
> (http://frankcondelli.com/exhaust.htm)
> _BusFusion_ (http://www.busfusion.com/) a VW Camper camping event,
> Almonte, ON, June 10 ~ 13, 2010
|