Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2010, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 3 Sep 2010 05:18:29 -0400
Reply-To:     Mike <mbucchino@CHARTER.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mike <mbucchino@CHARTER.NET>
Subject:      Re: rear valence trim?
Comments: To: Scott Daniel - Turbovans <scottdaniel@TURBOVANS.COM>
In-Reply-To:  <0fb601cb4b27$5c0e9b60$6801a8c0@PROSPERITY>
Content-Type: text/plain; format=flowed; charset="utf-8"; reply-type=response

water drain holes

-------------------------------------------------- From: "Scott Daniel - Turbovans" <scottdaniel@TURBOVANS.COM> Sent: Friday, September 03, 2010 1:17 AM To: <vanagon@GERRY.VANAGON.COM> Subject: Re: rear valence trim?

> I think you are thinking of the threaded inserts that are for the muffler > heat shield. > I think he is talking about holes in the body below that, on the very rear > lower edge. > > I just looked at two 85's, and 86, and two 87's. > looks like they are on 86 and later vans. > > > > ----- Original Message ----- > From: "Zolly" <zolo@FOXINTERNET.NET> > To: <vanagon@GERRY.VANAGON.COM> > Sent: Thursday, September 02, 2010 8:56 PM > Subject: Re: rear valence trim? > > >> As you can see, it is obvious that the holes are for bolts or screws to >> hold >> up the heat shield/splash guard. In this case, they are 6mm bolts. But >> most of the time, those little nuts that were fixed in the body, are >> spinning around and the bolts won't help. I have seen extra holes >> drilled >> for screws to do the same. >> Zoltan >> >> ----- Original Message ----- >> From: "Gregory Smith" <gfs@GREGORYFSMITH.COM> >> To: <vanagon@GERRY.VANAGON.COM> >> Sent: Thursday, September 02, 2010 7:02 PM >> Subject: rear valence trim? >> >> >> While under the van recently replacing my O2 sensor, I noticed four >> factory holes in the bottom edge of the rear valence. Is there a >> super-rare, super expensive trim or other piece that fits the holes? >> Just kinda wondering... >> >> Gregory Smith >> '88 Vanagon GL >> >> Smith Design Studio >> Small Building Company >> Olympia, WA >> 360-239-0429 >> gregoryfsmith.com >> >> >> -------------------------------------------------------------------------------- >> >> >> >> No virus found in this incoming message. >> Checked by AVG - www.avg.com >> Version: 9.0.851 / Virus Database: 271.1.1/3110 - Release Date: 09/02/10 >> 11:50:00


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.