Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (April 2011, week 4)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Sun, 24 Apr 2011 14:24:22 -0700
Reply-To:   David Vickery <david_vickery@YAHOO.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   David Vickery <david_vickery@YAHOO.COM>
Subject:   Re: Poptop Canvas Install
Comments:   cc: jim.felder@gmail.com
In-Reply-To:   <7491E3DD-500A-4523-B42D-C8F6F10E39D7@gmail.com>
Content-Type:   text/plain; charset=iso-8859-1

A couple final thoughts and resources on the poptop install. I found several good posts for doing this job as well as videos. Here is the best video I found. http://www.vimeo.com/12165017.

This video shows the canvas I installed. It is the higher end one that busdepot sells and also on gowesty's site($499). It is a german canvas (the brand is justKampers) and it is very different from the cheaper one from justkampers makes that many people have complained about poor quality and fit. As you can see, this one fits as well as the original.

In the above video, I noticed he made one mistake in his install, so look carefully at the way the old one is attached, maybe take photos to refer to. His mistake was attaching the top tack strip upside down. The top bead is supposed to fit into the channel instead of pushed behind it. On the bottom it goes the other way, with the flat side down and the bead completely behind the bar. That will make more sense when you look at where the screw holes are on your old canvas (they go through the top piping, not through the material). I guess if you get an acrylic one, they can be too big and you will have to figure out how to take up the slack. But most people really seemed to like the extra durability of the acrylic.

Reading the posts, there is another company in canada that makes one for a little bit more $, but is said to be even better quality. http://www.atelierspk.com/west_english.html The only nitpick I could have for this one is the side zippers are a little flimsy and the front window zipper is a little awkward.

I also found a positve post about one sold at CIP that is only $229 and the poster said it fits great. I can't find the post, but here is the canvas: http://www2.cip1.com/ProductDetails.asp?ProductCode=VWC-253-070-704-G

Other good posts. http://www.thesamba.com/vw/forum/viewtopic.php?t=310345 http://www.thesamba.com/vw/forum/viewtopic.php?t=446984&highlight=poptop+canvas

That's my 2 cents, Dave in Fort Collins

--- On Sun, 4/24/11, James Felder <jim.felder@gmail.com> wrote: > Excellent writeup, which I saved. > Can't wait for the next installment. >

> On Apr 23, 2011, at 9:56 PM, David Vickery <david_vickery@YAHOO.COM> > wrote: > > > Another gratifying project.  I starting replacing > my poptop canvas at about 4:00 today and stopped when it got > dark out.  Probably another hour tomorrow unless > something goes wrong.  I decided on the most expensive > version BusDepot sells after getting feedback from different > people.  The picture on their website doesn't do > justice to the higher end version that they sell and I > waited until I saw one in person to buy it.  They had > it on sale for $399 and the discount brought it down a bit > more.  These are a little bit of a PITA to put on, so > there is a nice feelig of accomplishment to do it. > > > > My tips for anyone doing this:  Start with the > right tools.  A small battery powered screw gun.  > A big drill is too bulky and will tire out yor arm and won't > reach into some of the places.  You also need a small > screwdriver for the corners.  A magnetic tip to help > hold the screws is essential. > > > > It works better to remove the bottom tack strip first > (tack strip is only on 86+ vans I think) and then you can > lay on the bunk and unscrew the top tack strip by lifting up > the canvas. > > > > When you take off the old one, it helps to leave it in > place laying on the upper bunk and laying out the new one in > its place.  If you don't you might install the canvas > upside down or even worse inside out. > > > > I almost made a mistake and started attaching the top > canvas tack strip from the inside.  That would have > ripped the front top corners which is what you probably the > biggest risk of the whole project. I am glad I remembered > how the orginal was on there. > > > > The expensive version fits great and I can see how > much harder this job would be with a lousy fitting one. > > > > The way I did it, I put the middle screw through the > top front, then the screws close to the corners.  I > kept referring to the old one to see where the corners were > in relation to the seams, but everything lined up perfectly. > You have to cut notches out of the bottom corner bead, just > the bead thing that sits under the tack strip in order to > make the turn.  That is how the original one was.  > Then I did the top back and the hardest part of the whole > thing was the top rear corners.  Laying on your back, > your arms get tired trying to get everything lined up and > stretched fairly taught.  This is where you will be > wishing you had a magnetic tip screw gun if you don't. > > > > After getting the corners tacked down, I filled in the > rest of the upper screws all around.  Then I put the > lower front tack strip on.  The tip here is watch out > for the botton front corner screws.  The fabric gets in > the way and wants to get caught under those screws.  It > did it on both sides, and I saw it befoe it did damage to > one side, and it tore the other corner just a little > bit.  Bummer. > > > > I only put a few screws in the top front, in case I > needed to adjust it, which it looks like I need to do.  > I stretched the fabric a little too much and have to back it > off a bit to get the corners to look perfect.  So the > tip is for this particular top, don't stretch it too much, > just get it nice and tight.  Look at how the seams > lined up with the corners on the original one. > > > > Wahoo, a new 3 window poptop! >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.