Date: Wed, 25 May 2011 23:20:18 -0400
Reply-To: Robert Stewart <robertmstewart@MAC.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Robert Stewart <robertmstewart@MAC.COM>
Subject: Re: Gas Vapors
In-Reply-To: <BAY152-ds1154D8E5FCB2CF5B115D6BA0730@phx.gbl>
Content-Type: text/plain; CHARSET=US-ASCII
Dennis,
I looked tonight at my air filter, there is a line coming from the top of the round filter that has been capped off. Isn't this suppose to connect to the charcoal filter? Where is that suppose to go? I assume I should connect that properly correct? I think a VW mechanic I used in Long Beach NY put a ball bearing in it and capped it off.
Rob
On May 22, 2011, at 7:21 PM, Dennis Haynes wrote:
> From: Robert Stewart [mailto:robertmstewart@mac.com]
> Sent: Sunday, May 22, 2011 7:09 PM
> To: Dennis Haynes
> Cc: vanagon@GERRY.VANAGON.COM
> Subject: Re: Gas Vapors
>
>
>
> I can't speak as to the Black Silicone looking thing he used on the seals.
> But I do believe it said it was ok for gas. Not sure.
>
>
>
> Gravity Valves are where?
>
> On top of each tank in the wheel wells.
>
>
>
> Vapor Recovery valve is on the left, right front or behind the air filter?
> What should I do with it once I locate it?
>
> In front of the air filter on the other side of the firewall. You should be
> able to hear it click each time the throttle is opened when the engine is
> running.
>
>
>
> I never have heard any pressure release sounds coming from the gas tank cap
> and this is my second van, so what is missing?
>
> Something is leaking somewhere. Just think later cars will generate a fault
> code when the tank can't hold vapor pressure.
>
>
>
> Thanks,
>
> Robert
>
>
>
> On May 22, 2011, at 6:58 PM, Dennis Haynes wrote:
>
>
>
>
>
> Silicon and gasoline. What was someone thinking. Most say on the tube not
> for use with gasoline or on head gaskets. It could just be a loose hose or
> one of the gravity valves on top of the expansion tanks. Also check the
> operation of the vapor recovery valve near the air filter. If all is well
> whenever you open the cap for filling you should hear some pressure
> escaping. After repairs the tank and vent system can be charged to 2-3 psi
> to make sure the vapors are kept in.
>
> Dennis
>
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
> Robert Stewart
> Sent: Sunday, May 22, 2011 6:06 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Gas Vapors
>
> A year ago my mechanic and I removed my new gas tank and installed the
> crossover pipe and a seal kit with all the rubber grommets and clamps. He
> used some special RTV silicone on all the rubber grommets before installing
> it.
>
> Now it's a year later and the smell of gas permeates outside the vehicle
> when I fill up. I have no idea what to do.
>
> I am at my wits end at this point.
>
>
> Either a hose is damaged, or a seal must have blown ( hard to believe with
> the new rubber and RTV silicone though).
>
> Does anyone have any advice?
>
>
> Thanks,
> Robert
> 88 Automatic Wolfsburg
> All New Fuel Lines
> All New Hoses
> Rebuilt Engine
|