Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (October 2011, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 10 Oct 2011 08:38:17 -0700
Reply-To:     Poppie Jagersand <poppie.jagersand@YAHOO.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Poppie Jagersand <poppie.jagersand@YAHOO.CA>
Subject:      Re: [Diesel-Vanagon] Re: Diesel starter differences,
              Was Re: Starter motor do-it-yourself rebuild
Comments: To: "Diesel-Vanagon@yahoogroups.com" <Diesel-Vanagon@yahoogroups.com>
In-Reply-To:  <166601cc871f$0e10a6d0$6401a8c0@PROSPERITY>
Content-Type: text/plain; charset=iso-8859-1

----- Original Message ----- > From: Scott Daniel - Turbovans <ScottDaniel@turbovans.com> > To: Diesel-Vanagon@yahoogroups.com; vanagon@GERRY.VANAGON.COM > Cc: > Sent: Monday, October 10, 2011 1:34:30 AM > Subject: Re: [Diesel-Vanagon] Re: Diesel starter differences, Was Re: Starter motor do-it-yourself rebuild > > re >> Some of us prime the fuel system by cranking and it takes about 1min to do so." > > doesn't sound right...........like there's air in the fuel line or something. > when a s regular prechamber type diesel vanagon engine .. > with 1.6 NA, 1.6TD, 1.9NA or 1.9 TD .. > with an inejction pump with a Injection Timing Advance 'choke knob' system on it .. > and working glow plugs .. > when all is right .. > cold starting will be instanteious, after glow-plugging it properly.  > like .....key on, cold start knob out, glow plug 'er a while.........".click -VROOOM"  ..to a steady idle. > that's how they start when everything is right. Yup, I agree. Normally should start on first compression stroke and mine normally does so if temps are reasonable (above freezing). But air enters the fuel system from time to time. A normal reason is changing something in the fuel system (fuel filter, injector return hoses etc.). Then pretty quickly all the Diesel drains back to the tank. Some will prime using a vaccuum pump, but others will just crank. Both the DD and reduction gear starter survives a few times of this. Abnormal, but not unusual issues are slow air leaks in the fuel system. Most common for me has been injector return hoses. Now more recently it was the injection pump shaft seal. I don't always get to fix them right away, but may end up driving like that for a week or two. Then the starter gets tasked with cranking a minute or so every time to purge the air. As I said in a previous post at least the aftermarket geared starter I got was not up to that task, while the DD has worked fine in the past, and now after rebuild I expect the DD starter to go maybe another decade. > I like the bosch rebuilt gear reduction starters just fine. > The older type that are not gear reduction work just fine too .. > if the starter and flywheel are both good. > never have had a reason to think about starter heat. > If the engine and fuel system and glow system are right .. > there is never any extended cranking. > > Scott   ----- Original Message -----   From: Poppie Jagersand   To: vanagon@GERRY.VANAGON.COM ; Diesel-Vanagon@yahoogroups.com   Sent: Sunday, October 09, 2011 8:20 PM   Subject: [Diesel-Vanagon] Re: Diesel starter differences, Was Re: Starter motor do-it-yourself rebuild       To validate the direct drive Diesel starter thermal capacity I did a repeated cranking test today then measured temps on various parts with an IR thermometer. I repeatedly cranked 10s, waited 10s, cranked 10s for 12 times so a total of 2min cranking and 2 min pause. Temp readings were as follows:   front casting (nosecone) 20C   Middle (stator) 30C   Rear (commutator and brushes) 40C   Ambient temp was 15C   Remember these are outside temps. Temp inside in the windings and commutator are obviously higher.   This suggests two things: The commutator is probably the limiting factor for how long you can crank continuously.   The starter is mainly cooled through the thermal path to the bell housing.   Why does anyone care? Some of us prime the fuel system by cranking and it takes about 1min to do so. I had an aftermarket geared starter and it was not up to the task. The Bosch geared starter may very well be better, but the one I have still needs a rebuild. (How do I get a broken stud piece out of the nose cone w/o damaging the casting or threads? I guess I can tru drilling it out in the drill press, but I'm afraid of the bit slipping and cutting into the much softer aluminium.)   Martin (and '82 Westy 1.9TD "Poppie")   ----- Original Message -----   From: Poppie Jagersand <poppie.jagersand@YAHOO.CA>   To: vanagon@GERRY.VANAGON.COM   Cc:   Sent: Friday, October 7, 2011 9:31:48 AM   Subject: Re: Diesel starter differences, Was Re: Starter motor do-it-yourself rebuild   Some more notes in this "all about the Vanagon D starter" thread.   Had a dead starter again. This time the solenpoid it appears. On my "home rebuilts" I disassemble the plunger part of the solenoid, clean, and very lightly grease (too much grease and the plunger seals against the barrel and sees "compression", so it won't pull the gear.) However I don;t do the contacts, which are more difficutl to get at. Here's a document on the solenoids for those who are interested:   www.venselenterprises.com/...files/solenoidrebuildingarticle.pdf   I had an extra used solenoid so swapped that one in instead. Then I'll go to my rebuilder to ask if he has any more used or rebuilt solenoids.   The broken solenoid also allowed me to measure the "pull" current. This is the normally very brief current which is only drawn for a subsecond while the plunger moves. Since my plunger never closed the contact the pull current remained on as long as the key was in cranking position. 10s or so of "on" caused smell/smoke which made me curious. Turns out pull current is 30A. This is ok instantaneously but pretty high for the wiring and spade connectors used if continuous. Normally when the plunger closes the pull coil is turned off and a smaller hold coil is left on holding the contactor and starting gear in position. This is the aspect that didn;t function on my solenoid.   Now for some questions:   On the newer, gear reduction starter, I was wondering if the rear motor part is shared between several Bosch starters? If so it would be possible to mate the motor part from a more common Diesel car starter to the Vanagon nosecone. Does anyone know what car models might be candidates? This could also be explored experimentally at a rebuilder patient enough to allow some roaming around in his boxes of old cores.   Along this vein, I have a vanagon starter nose cone from the newer starter, but with a broken and snapped stud in it. It is a pretty thin (M6 or smaller I think) hard metal alloy stud screwed into the alu nosecone. Anyone has tips on getting it our w/o damaging alu casting?   Finally some more info addressing the two variations of starters in the previous post below:   I weighed both the origonal direct drive (DD) and the newer gear reduction (GR( starter.   Weight   DD starter 8kg   GR starter 4Kg   Now some basic thermodynamics tells us that 8Kg of iron and copper can absorb twice the heat of 4kg, suggesting the old starter can crank quite a bit longer than the new (e.g. for those of us who prime the fuel system by cranking rather than using a vaccum pump). A very rough estimate is that the old starter can take 2-3min cranking, while the new one one should probably keep cranking to 1min or less. This was arrived at by putting 1kW into a motor simulator for a motor of similar weight and having it calculate the overheat time, so not very accurate, but maybe a rule of thumb.   Martin (and '82 Westy 1.9TD "Poppie")   ----- Original Message -----   From: Poppie Jagersand <poppie.jagersand@YAHOO.CA>   To: vanagon@GERRY.VANAGON.COM   Cc:   Sent: Monday, August 22, 2011 3:46:42 PM   Subject: Diesel starter differences,              Was Re: Starter motor do-it-yourself rebuild   A note for all users of the Diesel starters:(not just rebuilders)   The smaller newer gear reduction starter is likely more electrically efficient. It is also likely much cheaper to build.   However an advantage of the old, heavy direct drive starter is that it is much more abuse tolerant:   *The heavy weight makes it take much more cranking abuse before overheating.   *The construction is more durable. No flimsily attached and very fragile ferrite magnets.   *Fewer parts so less than can break.   So don't toss your old heavy original starter. Keep it around for when you get tired of replacing those new aftermarket (or Bosch) starters, and either rebuild it yourself, offer it to a listmember or find one of those (now rare) shops that will actually rebuild your starter, not just give you a replacement.   Martin (and '82 Westy 1.9TD "Poppie")   ----- Original Message -----   From: Poppie Jagersand <poppie.jagersand@YAHOO.CA>   To: vanagon@GERRY.VANAGON.COM   Cc:   Sent: Friday, August 12, 2011 10:38:02 AM   Subject: Re: Starter motor do-it-yourself rebuild   Here are some more starter observations. I pulled apart and compared the two different types currently available for our Diesel vanagon. As Neil, Bryan and others have noticed, when you get a rebuild you may end up getting the smaller swapped for the larger and vice versa.   member NYSwanderer put some photos on the web, and wondered what the differences between them are.   http://groups.yahoo.com/group/Diesel-Vanagon/photos/album/1381430081/pic/449269473/view?picmode=&mode=tn&order=ordinal&start=1&count=20&dir=asc   I took them apart and here is my side by side comparison:   The smaller is a gear reduction starter using a planetary gear and has a permanent magnet motor. The larger one is a direct drive  motor with windings in both stator and rotor connected in series. Both AFAIK meet spec.   I have a torque/power graph for the smaller one from a rebuilder.   If someone got a graph for the bigger it would be interesting to compare. Please scan and email me and I'll post both.   In theory the larger starter could have both a higher peak torque and a higher max rpm. That comes from the fact that both rotor and stator windings are connected in series. When stalled or at very low rpm, the high current will increase the magnetic field in both the stator and rotor. By contrast, the permanent magnet motor has a fixed magnetic field from the ferrite magnets (that may even go down if the starter gets hot).   For the series motor as the rpm increases the magnetic field weakens. This field weakening yields a lower back EMF in the windings, and thus allows for a higher RPM.   These are differences you learn in a motor text book. The gear reduction and design of the smaller starter may very well make up for them. That's why it would be interesting to compare test graphs.   Mechanical differences:   I don't think many internal parts interchange. I tried to use the studs from one on the other, but threads were different. Brushes and brush holders are different.   At best there seems to be some chance that solenoids and end bushings may be the same, but I need to check. Or someone with Bosch data tables can find out.   The smaller one have very brittle ferrite magnets. Don;t drop your tools or they can/will shatter. The bigger one has robust copper windings in the stator.   Another note on the smaller starter: nyswanderer remarked that he saw no Bosch markings on his, so it must be an aftermarket. I however got a smaller starter that a friend had brought from Germany. That is an original Bosch with markings. I got another one with no markings.   Martin (and '82 Westy 1.9TD "Poppie")   ----- Original Message -----   From: Martin Jagersand <jag@CS.UALBERTA.CA>   To: vanagon@GERRY.VANAGON.COM   Cc:   Sent: Saturday, August 18, 2007 9:12:00 PM   Subject: Starter motor do-it-yourself rebuild   I just rebuilt the starter for my '82 Diesel Westy. Last time I did it was   in '99, I think, so the previous rebuild lasted about 8 years.   Bosch rebuilt starters can run near $200 nowdays, but rebuilding it yourself   is not hard. Here are some tips:   (Edit 2011: I was quoted from 200 to $400 for a Bosch rebuilt, $100 to 300 for others)   First check that the problem is really the starter. Measure the voltage over   the starter itself while cranking, ie from the positive iput terminal on the   starter to the starter housing. If it's 8-10V and the starter still is   cranking slowly the starter is most likely bad. If battery voltage is ok but   voltage at starter is low check voltage drop in the positive and negative   circuit. When I measured I had .2V drop in the neg circuit and .9V in the   positive. Of the .9V .7V was over the solenoid and .2V in ther actual cable.   If it is not starting at all, no noise, no click, despite having 12V at both   starter and solenoid, check connections to the solenoid, and then between   solenoid and starter. This time I found that the metal tab running from the   outside of the soloid terminal and connecting the solenoid winding was   sheared off. I soldered on a flat piece of copper (from a water pipe ground   strap) to fix it.   So you determined that its the starter. All Bosch starters, gas or diesel   have the same basic design, but the sizes and housings are different between   different models. Get the right parts!   Wear parts are basically:   1/ Bushings: 3 total. One in each end, and one in the middle. The latter I   don't think carries much load. Cost: about $1 each from the Bosch   distributor.   2/ Brushes: 4 in total. You can buy either a brush assembly for $45 with the   4 brushes already mounted, or 4 loose brushes for about $15 total. If you   get loose brushes get ones with small u-shaped metal ends welded to the   copper braid. They are much easier to solder to your brushholder.   The above is Bosch prices VW dealer prices are about twice as much.   Rebuild procedure:   1. Unscrew the two small screws on the commutator housing (back) this   releases the brush holder.   2. Unbolt the two studs in the back. Now the commutator end comes off after   removing a circlip on the end of the shaft, and the rotor is loose, but   don't pull it off yet.   3. Loosen the 3 screws holding the solenoid to the front housing.   4. Between the solenoid and the starter motor is a small rubber piece. See   if you can loosen it. Carefully wiggle and separate the front housing.   5. Solenoid and starter can be separated at the solenoid end. Take off the   solenoid. (To prevent binding wipe off any dirt or corrosion on the solenoid   plunger before reassembly)   6. Determine shape of bushings. The gear end bushing is in the bellhousing   on starters for transverse engine models, and in the front housing on   longitudinal engines. Replace front and rear bushings if worn.   7. To get at the middle bushing remove the ring and c-clip in front of the   gear. Slide off gear assembly. Take out plate holding middle bushing.   Replace if worn.   8. Check brushes. New brushes have about 8mm between the tip and the copper   braid. I'd replace them if they are more than half worn. Also if the   bushings were really bad the starter shaft has been riding out of center,   and the brushes have been wearing irregularly and need replacement.   9. Snip off the braided copper holding the old brushes. Don't lose the   springs! File off any remains from the brush holder. Solder on new brushes.   Make sure they are soldered well. Each brush will pass 100's of amps at   startup!   10. Inspect the commutator. If pitted (from arcing) sand/file down until clean and smooth   copper. If out of round use a lathe.   11. Assemble the parts. Grease bushings and gears lightly. You don't want   grease on the commutator or too much so that it can spatter on the clutch.   --   Martin Jagersand   University of Alberta   http://www.cs.ualberta.ca/~jag/   [Non-text portions of this message have been removed] ------------------------------------ Yahoo! Groups Links <*> To visit your group on the web, go to:     http://groups.yahoo.com/group/Diesel-Vanagon/ <*> Your email settings:     Individual Email | Traditional <*> To change settings online go to:     http://groups.yahoo.com/group/Diesel-Vanagon/join     (Yahoo! ID required) <*> To change settings via email:     Diesel-Vanagon-digest@yahoogroups.com     Diesel-Vanagon-fullfeatured@yahoogroups.com <*> To unsubscribe from this group, send an email to:     Diesel-Vanagon-unsubscribe@yahoogroups.com <*> Your use of Yahoo! Groups is subject to:     http://docs.yahoo.com/info/terms/


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.