Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2012, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 19 Feb 2012 10:31:13 -0600
Reply-To:     Jim Felder <jim.felder@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Jim Felder <jim.felder@GMAIL.COM>
Subject:      Re: Mike B's Method For Removing Outer CV Joints
In-Reply-To:  <BAY152-ds12A5EF0EBC57C2AEF781A1A0610@phx.gbl>
Content-Type: text/plain; charset=ISO-8859-1

On internally damaged allen bolts, I have had good luck with the extractors that are more or less conical in shape, they fit down over the outside of the bolt and the sharp reverse threads dig into the metal head and remove the bolt. They are available pretty much everywhere you buy tools.

Jim

On Sun, Feb 19, 2012 at 10:10 AM, Dennis Haynes <d23haynes57@hotmail.com>wrote:

> Can you get the other 5 out? If so do so. You can then try turning the > axle shaft spinning on the one screw loosening it slightly. Then and > oversize Allen wrench or internal bolt extractor can turn it out for you. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf > Of J Stewart > Sent: Sunday, February 19, 2012 10:40 AM > To: vanagon@GERRY.VANAGON.COM > Subject: Mike B's Method For Removing Outer CV Joints > > Well, I did it to myself (someone even cautioned me about this) , back > between Christmas and New Years I pulled my dash to replace my locked up > front blower motor, not a fun job! I stated here on this list that the next > job, left side CV joints was next and it would be a piece o' cake compared > tot the blower motor. I did the right axle last summer and it was not a bad > job, however this morning on the very first CV bolt I tried to remove from > the outer joint I managed to round it out. I even cleaned inside the bolt > head with a pick and tapped the hex head socket into head of the bolt to > seat it as far as possible, and it still stripped out-no need to go further > at this point. I went to "Been There, Done That" and found the write up on > CV joints with an addendum by Mike B. on removing the outer 46mm nut on the > axle, yada, yada, yada. He says this is the "short version" of how to do > this, and I'm not quite getting it-where can I find the "long version"? Not > sure now if this is a job I'm going to finish today, it being Sunday and I > am not off work tomorrow, it's beginning to look like a Saturday morning > job for next weekend. TIA for any advice. > > > > > Jeff Stewart >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.