Date: Sat, 5 May 2012 10:46:55 -0400
Reply-To: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject: Re: last minute engine swap questions
In-Reply-To: <3A50274E-274D-4DDF-BC97-5EC543D62B66@comcast.net>
Content-Type: text/plain; charset="US-ASCII"
This mount clears the flywheel. I do get concerned that it is only a two
point mount especially for a complete engine assembly. I actually have a
heavy duty three point but I have no idea where to now get one. The two
point makes all the difference when you have to split the case.
Dennis
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of
George Laubach
Sent: Saturday, May 05, 2012 9:59 AM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: last minute engine swap questions
Thanks Dennis!
I see that is a "2 position" attachment. Is it good enough to spin the
engine 360 degrees? And should I keep the flywheel off until I remove the
engine with the crane? Or does this adapter allow the flywheel on the engine
while on the stand?
Skip
Sent from my iPad
On May 5, 2012, at 8:47 AM, Dennis Haynes <d23haynes57@hotmail.com> wrote:
> http://cbperformance.com/catalog.asp?ProductID=1051
>
>
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On
> Behalf Of George Laubach
> Sent: Saturday, May 05, 2012 9:12 AM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Re: last minute engine swap questions
>
> Where can I source that clever "half-circle" attachment to an engine
stand?
>
> I have the red HF engine stand. My engine (1.9 WBXR now with the GW
> 2200
> kit) will be back from the machine shop soon (with flywheel attached).
> When I removed the engine a few months ago I used the engine stand
> hardware (with some long bolt modifications) but was not comfortable
> with how the stand/bolts did not have clearance from the teeth of the
flywheel.
>
> Any advice and sourcing please? Thank you.
>
> Skip
> '84 Westy 1.9L case/96mm pistons (something like that)
>
> Sent from my iPad
>
> On May 4, 2012, at 11:51 PM, Scott Daniel - Turbovans
> <scottdaniel@TURBOVANS.COM> wrote:
>
>> on some engine stands , the engine will fit on it with the flywheel
>> in place.
>>
>> I've worked on lots of them on the ground ..
>> get some blocks under it at least.
>> there are a few fasteners on the underside you'll be working on.
>>
>> hard to do good car work sitting on the ground.
>> a small stool perhaps ...sometimes.
>>
>>
>> On 5/4/2012 5:00 PM, pickle vanagon wrote:
>>> Being that I don't have a Bell-housing, with this stand can I bolt
>>> the plate onto the engine without removing the flywheel?
>>>
>>> Even though the makes it easier, the floor does work too right? Or
>>> are there fasteners I'll have a lot of trouble getting access to? I
>>> don't mind doing work sitting on the ground as long as it is
>>> reasonably
> feasible.
>>>
>>>
>>> On Fri, May 4, 2012 at 4:19 PM, HotelWestfalia<zolo@foxinternet.net>
> wrote:
>>>
>>>> That engine stand from HF is great, especially if you would have a
>>>> bell housing as I do. As long as you can get four bolts holding it.
>>>> Lifting up is heavy but two strong guys can do it, just bolt the
>>>> engine onto the plate first and then put it on the engine stand after.
>>>> It's great to have the ability to work without bending down and be
>>>> able to turn the engine the way you like it.
>>>>
>>>> That engine lifter I made, and sold a few, is great to install and
>>>> uninstall an engine from the van using a drip tray to pull the
>>>> engine on the ground with, small ropes attached on each end through
>>>> holes made by you.
>>>> Simplicity at it's best.
>>>>
>>>> Zoltan
>>>>
>>>>
>>>>
>>>> ----- Original Message -----
>>>> From: "Jim Arnott"<jrasite@EONI.COM> To:<vanagon@GERRY.VANAGON.COM>
>>>> Sent: Friday, May 04, 2012 12:41 PM
>>>> Subject: Re: last minute engine swap questions
>>>>
>>>>
>>>> HF cheap engine stand makes it easier....
>>>>> http://www.harborfreight.com/**750-lb-capacity-engine-stand-**3291
>>>>> 5
>>>>> .html<http://www.harborfreight.com/750-lb-capacity-engine-stand-32
>>>>> 9
>>>>> 15.html>
>>>>>
>>>>> -----Original Message-----
>>>>> From: pickle vanagon
>>>>> Sent: Friday, May 04, 2012 12:13 PM
>>>>> To: vanagon@GERRY.VANAGON.COM
>>>>> Subject: [VANAGON] last minute engine swap questions
>>>>>
>>>>> My engine swap (1.9 for rebuilt 2.1) is coming up in a week.
>>>>>
>>>>> I think I pretty much have my ducks in a row (we'll see though!).
>>>>> I do have one question:
>>>>> I'll be dropping the engine with Zoltan's "sawhose over the engine
>>>>> compartment" method.
>>>>>
>>>>> My question is: do I also want some kind of hoist available to
>>>>> help with moving the engine around my workspace, or to elevate it
>>>>> while transferring components? Or will it be reasonable to carry
>>>>> around the floor (I'm assuming I'll be able to enlist a volunteer
>>>>> to help with carrying, at
>>>>> least) and bolt things on with it on the floor?
>>>>>
>>>>> (Note: making hoist-like contraptions myself to help are not an
>>>>> option because I'm going to be time-limited and don't want to give
>>>>> up any time I can be focused on doing the swap. But if having an
>>>>> engine hoist will make transferring components much easier I'm
>>>>> willing to pay Harbor Freight for
>>>>> one.)
>>>>>
>>>>> Thanks for any advice!
>>>>> Wes
>>>>>
>>>>>
>
|