Thanks Dennis. Out of curiosity I shaped, and duct taped a toilet roll (such Kustom Werk) to approximately fit in outlet of air bypass. Blowing into the outlet, I opened and closed the CO screw. Though this was a buck-shee method, it really seemed to me that with screw in all the way, the air bypass was closed. As per your other post, I measured the voltage output of the O2 sensor (after disconnecting, engine off) while turning the CO screw. I saw higher voltages ( ~ 0.8 ) and the output fluctuated some (maybe analogue VOM better for this purpose?) but in general, adjusting the CO screw affected the O2 voltage output. Maybe the sensor had cooled down prior to test (had engine up to temp, then it sat for about 10 minutes) Will recheck timing then test O2 voltage output again, right after engine up to temp. Not sure why a PO set the CO screw all the way in (bypass closed off). Compensate for a vacuum leak? Worn throttle body valve? I have yet to make a smoke tester but have re-tested the air intake bellows and its' 2 pipes for leaks (none) and repaired a small leak at ISV 3 way boot. (yes. Permatex silicone and small shaped piece of fuel hose can repair a leak at the small pipe) btw. Here's a neat explanation, "how to" and video made by Chris Corkin (aka Tencent) on measuring the AFM. Really cool and useful. http://www.thesamba.com/vw/forum/viewtopic.php?t=369815&highlight=afm+test video link here:
Neil.
On Sat, Jul 7, 2012 at 11:19 PM, Dennis Haynes <d23haynes57@hotmail.com> wrote: > The air bypass or mixture adjusting screw will not bypass enough air for the > AFM vane to stay closed. If it could than the air cooled engines would have > a problem as the AFM vane has to open to run the fuel pump. It is just a > trim adjustment. It must be noted that when trying to adjust this you need > to disconnect the O2 sensor and restart the engine after the disconnect to > not have any O2 sensor compensation. Adjust fir ~.5 volt at the sensor with > it disconnected. Then when you connect it you should see the system react > and change the sensor readings. Normal fluctuation should be ~.2 to .8 volt. > > Dennis > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of > neil n > Sent: Friday, July 06, 2012 4:52 PM > To: vanagon@GERRY.VANAGON.COM > Subject: At Idle: AFM Flap, CO Screw Relationship. Explanation Found
> http://www.race.nangreaves.com/golf/FU01/ch7.6.html
> .... I had figured that the air bypass, at idle, would allow the AFM > to stay closed. e.g. that air bypassed this flap and that the mixture was > controlled by adjustment of air only, via the CO screw. Not true it seems.
-- Neil n 65 kb image Myford Ready For Assembly http://tinyurl.com/64sx4rp '88 Slate Blue Westy to be named. '81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/ Vanagon VAG Gas I4/VR Swap Google Group: http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines |
Please note - During the past 17 years of operation, several gigabytes of
Vanagon mail messages have been archived. Searching the entire collection
will take up to five minutes to complete. Please be patient!
Return to the archives @ gerry.vanagon.com
The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.
Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.