Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (August 2012, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 2 Aug 2012 17:07:48 -0700
Reply-To:     Alistair Bell <albell@SHAW.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Alistair Bell <albell@SHAW.CA>
Subject:      Re: Caliper Bleeder Screw: RF Typically Seize More Often?
Comments: To: neil n <musomuso@GMAIL.COM>
In-Reply-To:  <CAB2RwfgCq2ufZ3idmTGynex4sHrrsQn3jXd=rW2d9ejpdCVNyg@mail.gmail.com>
Content-Type: text/plain; charset=us-ascii

I'm afraid my advice is to buy another caliper and work on stuck bleeder at your leisure.

alistair

On 2012-08-02, at 3:55 PM, neil n wrote:

> Hi all. > > Took my '88 Westy to a shop. Shortly after work done, felt a short > noticeable shudder braking at highway speeds. In checking the shops > work. (wheel fasteners, etc.), noticed the RF bleeder was untouched. > It won't turn, the other 3 do. Shop had flushed the brakes. Asked the > shop about this screw, they said they bled that wheel at a hose union > (but I can't see any wrench marks at any of those unions...... That's > another story) > > Before taking van to shop, I sprayed penetrating fluid on bleeder > screws well in advance. Maybe I missed spraying the RF bleeder > but..... > > Is the RF bleeder any more prone to seizing than the LF bleeder? > Strange question but I'm trying to determine if it's worth tackling > this part or just wait until I do both calipers, hoses etc. > > I saw Alistairs page, and a few comments (thanks Scott) on getting a > stuck bleeder loose. > > What I've done: > > - applied penetrating fluid > - applied heat to caliper body (butane torch, nothing too hot) > - tapped on the end of the bleeder with a small hammer > - picked rust/dirt away from threads at caliper body > > I plan on wrapping a small rag around the bleeder and soaking it with > penetrating fluid to keep it all "wet". > > Any other tips to loosening the bleeder are welcome! > > Neil. > > > > -- > Neil n > > 65 kb image Myford Ready For Assembly http://tinyurl.com/64sx4rp > > '88 Slate Blue Westy to be named. > > '81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/ > > Vanagon VAG Gas I4/VR Swap Google Group: > > http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.