Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (November 2012, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 8 Nov 2012 20:52:45 -0800
Reply-To:     Stuart MacMillan <stuartmacm@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Stuart MacMillan <stuartmacm@GMAIL.COM>
Subject:      Re: Transmission input shaft play?
Comments: To: Scott Daniel - Turbovans <scottdaniel@turbovans.com>
In-Reply-To:  <509C7D56.2040509@turbovans.com>
Content-Type: text/plain; charset="us-ascii"

He's talking about the input shaft to the transmission as I understand him, not the output, which is as you say.

Stuart

From: Scott Daniel - Turbovans [mailto:scottdaniel@turbovans.com] Sent: Thursday, November 08, 2012 7:50 PM To: Stuart MacMillan Cc: vanagon@GERRY.VANAGON.COM Subject: Re: Transmission input shaft play?

'ball bearing channels' ?

I thought it was well understood that the junction spot ..where a stud keeps the two shafts locked together ..with a splind sleeve over it, allows sfor up/down, left/right wiggling.

On 11/8/2012 5:28 PM, Stuart MacMillan wrote:

Normal radial play, there should be no axial play. That's the clearance in the ball bearing channels, and why you need a pilot bearing to support the other end of the shaft.

Stuart

-----Original Message----- From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Tabe Johnson Sent: Thursday, November 08, 2012 11:13 AM To: vanagon@GERRY.VANAGON.COM Subject: Re: Transmission input shaft play?

Yes, I meant radial play, not axial.

tabe

--- On Tue, 11/6/12, neil n <mailto:musomuso@gmail.com> <musomuso@gmail.com> wrote:

From: neil n <mailto:musomuso@gmail.com> <musomuso@gmail.com> Subject: Re: Transmission input shaft play? To: greentabe-vanagon@yahoo.com Cc: vanagon@gerry.vanagon.com Received: Tuesday, November 6, 2012, 10:40 PM If you're talking about side to side play, that's normal.

The input shaft is held onto another shaft (can't recall part name) with a small stud. There is a gear/sleeve that slides over both, but my guess is that even with that gear, there's still enough play to allow side to side movement.

Some images of what I mean (this is an air cooled, but same idea):

https://picasaweb.google.com/musomuso/InputShaftRRDKAirCooledTransmiss ion#

Neil.

On Tue, Nov 6, 2012 at 9:18 PM, Tabe Johnson <mailto:greentabe-vanagon@yahoo.com> <greentabe-vanagon@yahoo.com> wrote:

I was looking at a (used) manual transmission today and

it had maybe 1/8" to 1/4" of play at the end of the input shaft. How much is normal/acceptable?

tabe johnson/90MV

-- Neil n

65 kb image Myford Ready For Assembly http://tinyurl.com/64sx4rp

'88 Slate Blue Westy to be named.

'81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/

Vanagon VAG Gas I4/VR Swap Google Group:

http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-e ngines =


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.