Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2013, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Fri, 8 Feb 2013 20:27:55 -0800
Reply-To:   neil n <musomuso@GMAIL.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   neil n <musomuso@GMAIL.COM>
Subject:   Re: Electrical "Locking" Terminal Info + Question
Comments:   To: Dennis Haynes <d23haynes57@hotmail.com>
In-Reply-To:   <BAY152-ds685A8A6BE6B2D04F22B18A0040@phx.gbl>
Content-Type:   text/plain; charset=ISO-8859-1

Yes!

I got something similar from my non dealer parts vendor. Fixed up my ECT and hall sockets real good!

You can see the new yellow leads in RH of image:

https://lh6.googleusercontent.com/-UFKqa3oP_j8/TL4fULXjShI/AAAAAAAAD9k/4tTQslBmhxc/s720/28aConnectorWIRESNearBlock.jpg

re: "punish"

This is how I learn. Heh. Kidding. But I am painfully aware that leaving the relay "floating freestyle" (not secured to a proper socket) did not help. But I agree; that joint was doomed. And, why would the manufacturer use a PCB? The newer 109 relay is like these:

https://picasaweb.google.com/musomuso/MiscVanagonWestyPics#5842008141534071810

Neil.

On Fri, Feb 8, 2013 at 8:12 PM, Dennis Haynes <d23haynes57@hotmail.com> wrote:

> Our dealer has "pigtails" with the terminal already crimped in place. Use a > butt connector to splice to harness. They are available in various wire > gauges to handle most any load. That solder joint looks like it was > defective from day one especially if that is still the flux oozing out. > Don't punish yourself for the failure. > > Dennis > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of > neil n > Sent: Friday, February 8, 2013 9:44 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Re: Electrical "Locking" Terminal Info + Question > > Thanks Dennis. > > Point taken. Will NOT mismatch. I had shrink wrapped the terminals but for > various reasons, (including my install), this happened: > > close up shot of relay printed circuit board. Cracked solder is for 30 into > relay: > > https://lh4.googleusercontent.com/-h3JODsFUDHM/URHsPfqBbZI/AAAAAAAAGy4/5DkyK > weHpnc/s576/Jetta%2520Power%2520Supply%2520Relay%2520Solder%2520Crack.jpg

-- Neil n

65 kb image Myford Ready For Assembly http://tinyurl.com/64sx4rp

'88 Slate Blue Westy to be named.

'81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/

Vanagon VAG Gas I4/VR Swap Google Group:

http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.