Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 2013, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 7 Mar 2013 19:16:48 -0900
Reply-To:     Mark Tuovinen <aksyncronaut@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Mark Tuovinen <aksyncronaut@GMAIL.COM>
Subject:      Re: Worst of all Vanagon Jobs
Comments: To: Jonce Fancher <streetbugs@frontier.com>
In-Reply-To:  <fb13bf$aer0t9@out02.dlls.pa.frontiernet.net>
Content-Type: text/plain; charset=ISO-8859-1

Next time you need a front heater blower replaced I will gladly do it for you and all you have to do in return is the starter on my syncro when it fails. I probably just jinxed myself on that on. Lol

Mark in AK `87 Westy Syncro

On Sun, Mar 3, 2013 at 2:09 PM, Jonce Fancher <streetbugs@frontier.com>wrote:

> My worse night mare might be the front heater blower assembly. > I have pulled a few out of vanagons that I have parted out and its a > PITA just to get it out. Mine has been fine and I keep a few spares > but Man I hope I never go down that road. > Worse one in the past year has been R/R the fuel lines over the Gas > tank, Wait that one was within the past 8 Hours. Stinks big time to > get all the crap out of the way and empty the tank of fuel then pull > the main filler neck, It would REALLY Stink If you had to do it on > the ground or on jack stands. I Have a lift so it is a bit easier, I > know I am a Puss! But I saved my pennies and got it years ago. > Just got to put the tank back it and ready to go! > > All in good fun! > Jonce > > Rear heater is nothing. >> I nominate changing out the pedal assembly. Or even worse ..adjusting >> the push rod length for the clutch master cylinder. >> >> It's very important IMO to have the rear heater valve on at least >> partially all year long. >> Keeping fresh coolant circulating through the rear heater helps prolong >> its life . >> >> I was just reading somewhere where they said to pre-mix anti-frz and >> water before pouring in the mix .. >> rather than add say 1/2 gal a-frz followed by 1/2 gal water to get a >> 50/50 mix. >> I have not found that ever to be an issue .. >> and it would not be for a rear heater core if the valve is kept at least >> partially open at all times. , all year round. >> >> re rear seat .. >> inconveniently VW made the plastic ( maybe it's fiberglass ) cover for >> the rear heater on GL models so it's captured by the bar going across on >> a Z Bed rear seat. You only have to remove that once .. >> then you just cut away a little bit of that cover on the bottom >> ,,,,,,,,,,,,,from then on the cover comes right off. >> I've had someone tell me that you can cut out that round bar going >> across there too .. >> and the Z bed rear seat still works just fine. >> >> wow..I have not found rear seats to be dangerous in any way. >> R & R many syncro transmissions ? ....they're lots of fun. >> >> I have about 6 rear heater assemblies in my used parts stash. >> >> stay cozy ! >> scott >> >> >> >> >> On 3/3/2013 1:08 PM, Jim Felder wrote: >> >>> All the above. But, before you tear into that >>> nearly-worst-of-all-Vanagon-**jobs, check out the valve. There is an >>> o-ring >>> under that can leak. Also, when people carelessly put in coolant water >>> without mixing it, the water can collect in the out-of-the-way heater and >>> freeze, popping open the housing at the valve. >>> >>> The valve itself also can leak. There is not much in replacing any of it, >>> the hard part is getting to it because of the rear seat. You can get hurt >>> about as badly on that as the transmission falling on you. Be careful. >>> >>> I do not have a valve or any of that, but I do have the housing, blower >>> and >>> a good core. >>> >>> Jim >>> >>> On Sun, Mar 3, 2013 at 1:51 PM, Finn Runyon <finnrunyon@gmail.com> >>> wrote: >>> >>> Our van is nearly ready to hit the road after a year's work to rebuild >>>> the >>>> engine. I bought this one with a blown engine. The rear heater os >>>> leaking, and I am wondering if the valve tends to leak, the O ring, the >>>> core? If there is a most common failure I will do that or do generally >>>> rebuild the whole unit? The valve defiantly is leaking. >>>> Thanks, >>>> Finn Runyon >>>> 87 Westy Roo >>>> 89 Westy Pooh >>>> 12 GTI Autobahn >>>> >>>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.