Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (March 2013, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sun, 17 Mar 2013 11:21:27 -0700
Reply-To:     Alistair Bell <albell@SHAW.CA>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Alistair Bell <albell@SHAW.CA>
Subject:      Re: Adjust Rear Bed? (and rear seat re-foam pics)
Comments: To: neil n <musomuso@GMAIL.COM>
In-Reply-To:  <CAB2RwfiVFsPEORYEy+c7Oe9-FnnKy_avZs3Bp8hBkPXrWOnk6g@mail.gmail.com>
Content-Type: text/plain; charset=us-ascii

Neil,

that is a very nice job, well done. My rear bed needs the same treatment, your work certainly will help me figure out what to do.

I've examined the folding mechanism (when I had the bench in parts), and I could not see any easy adjustment of the hinges themselves. I do think that the various metal-to-metal rubbing spots wear a bit and makes the hinges a little loose. I gave re-peaning the hinges a bit of a try, no real luck. The little spring loaded catch was slightly bent (and worn), I tried to straighten that up. All in all the hinge mechanism felt more sloppy than I think it should.

Note: I did all this mucking around with bench and bed in workshop, so it was easier to get at things etc.

Off hand I can't think of why your bed is misaligned. One thing I noticed and took some time to fix, was some of the machine screws that hold the seat bottom and the seat back to the frame do not hold well. They are machine screws, not woodscrews. They engage into metal on the foam side of the plywood.

On second thought, one possible source of misalignment might be hinge to side plywood bolts. Just a wag though.

cheers and good luck

alistair

PS I seem to recall that there are some differences in bed mechanism over the years. One thing is the presence of metal braces on the seat bottom that when the bed is deployed, rest on the top surface of storage frame. But my memory is hazy on this.

On 2013-03-17, at 10:44 AM, neil n wrote:

> Hi all. > > Finally got my rear bed re-foamed and recovered. Pics and notes here. > I may add more. > https://picasaweb.google.com/musomuso/RearSeatBedReFoamEtc# > > Anyhow..... > > When folded out, the rear bed has always had a 3/4" - 1" gap on the > driver side between bed bottom and storage frame. A few years ago, I > tightened a bolt or other on this side so maybe I put it out of > alignment. > > Is there a typical part or parts that wears, or, is there an > adjustment, loosen a part or two, reposition, that might address this? > It's a narrow spot to work in so direction toward the likely offender > would be appreciated! > > Thanks > > Neil. > > > -- > Neil n > > 65 kb image Myford Ready For Assembly http://tinyurl.com/64sx4rp > > '88 Slate Blue Westy to be named. > > '81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/ > > Vanagon VAG Gas I4/VR Swap Google Group: > > http://groups.google.com/group/vanagons-with-vw-inline-4-cylinder-gas-engines


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.