Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (July 2013, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Thu, 11 Jul 2013 12:01:32 -0700
Reply-To:   Stacy Schneider <vwcrewman@GMAIL.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Stacy Schneider <vwcrewman@GMAIL.COM>
Subject:   Re: Oil plug
Comments:   To: Scott Ohana <scottdaniel@TURBOVANS.COM>
In-Reply-To:   <51DD0B44.3090708@turbovans.com>
Content-Type:   text/plain; charset=us-ascii

Look on Samba . There is a guy who sells extended length plugs . Every water boxer engine should have one of these in it. . The original plug is too short . Best $9.00 I've spent in a long time.

-Stacy

On Jul 10, 2013, at 12:20 AM, Scott Ohana <scottdaniel@TURBOVANS.COM> wrote:

> If it's in a book somewhere it's probably 18 to 23 ft lbs, would be my > guess. > and yet.. > in 50 years of nearly full time car repair I have never heard of anyone > using a torque wrench on a drain plug. > It's not the standard.. > 'just right by hand' is the standard. > > Do YOU tighten your drain plugs with a torque wrench ? > if so..first time I've ever heard of anyone doing it. > > and there are a few techs that make everything 'gorilla tight' ......and > very incorrectly. > > On 7/9/2013 11:33 PM, Aristotle Sagan wrote: >> Did you ask them what torque spec they tightened it to? >> Expect blank looks on their faces. >> >> tim in san jose >> >> On Tue, Jul 9, 2013 at 11:12 PM, Scott Ohana <scottdaniel@turbovans.com>wrote: >> >>> yup.. >>> that happens sometimes. >>> Not too commonly. >>> One of the vanagons I have cared for over the last few years has that >>> issue. >>> 50 others do not. >>> >>> >>> >>> On 7/9/2013 11:00 PM, C Snyder wrote: >>> >>>> I had an almost bad experience today with my 1987 Vanagon's oil plug. >>>> >>>> >>>> I had taken it to where I usually take my van for repairs and oil >>>> changes. In a short while they came and told me that when they went to >>>> replace the oil plug, the plug stripped out in the bottom of the engine. I >>>> really do not understand this as I have never had any problems with the

>>>> plug. they said that since that plug has been taken out so many times, that >>>> because it is aluminum, and the plug is steel that some times they will

>>>> strip out the threads. >>>> >>>> >>>> To fix it, they were able to put in an over sized "Piggy back" oil plug. >>>> It seems to be ding fine but, am just wondering if any one else has ever >>>> had this type of problem as I have been on this list several years but,

>>>> have never heard it mentioned here before. >>>> >>>> >>>> Thanks for any ones opinion on this. >>>> >>>> >>>> Chris S. >>>> >>>> >> >> -- >> Where ever you are, there you be. Unless you're driving my van, in which >> case, you ain't got there yet. >>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.