Date: Wed, 17 Jul 2013 13:53:40 -0700
Reply-To: Stuart MacMillan <stuartmacm@GMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Stuart MacMillan <stuartmacm@GMAIL.COM>
Subject: Re: replacing fuel tank
In-Reply-To: <CAObFu5p2sB1JrXw1mKeAPgNbBjKrDtLDvdMXFMzAJZaAyN63kA@mail.gmail.com>
Content-Type: text/plain; charset="utf-8"
Yes, outlet is the only difference.
Stuart
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Sudhir Desai
Sent: Wednesday, July 17, 2013 1:18 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: replacing fuel tank
does it go in the same as the old tank? (i've been off/on considering replacing mine)
On Wed, Jul 17, 2013 at 4:14 PM, Dennis Haynes <d23haynes57@hotmail.com>wrote:
> Actually the later tanks take an 11mm hose. The 86 and later vans do
> not use a filter before the pump, just the inlet screen in the tank.
> If you have sand and debris in the tank then most likely the vapor
> recovery system on top has broken, leaking parts and road stuff has been getting inside.
> With few exceptions today's fuel supplies are very clean. The larger
> filter has more capacity and filters smaller particles to protect the injectors.
> The fuel system recirculates the fuel so the stuff in the tank should
> actually get cleaner as you drive. The recommended service interval
> for the later fuel filter is 30K miles. Filters before the pump
> increase the possibility of vapor lock and are no longer used by most
> manufacturers. In fact many now put the pump inside the tank or use a
> pre-pump. If buying a tank I would go with the 11mm outlet.
>
> Dennis
>
> -----Original Message-----
> From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On
> Behalf Of Skip
> Sent: Wednesday, July 17, 2013 3:05 PM
> To: vanagon@GERRY.VANAGON.COM
> Subject: Re: replacing fuel tank
>
> Close to a purchase of a new fuel tank, myself. - '84. I experience
> random acts of fuel starvation at speed and questionable idle
> conditions which may/may not have anything to do with fuel flow or
> fuel blockage in the tank (reference Alistar's narrative), but I'm
> also suspicious. I can personally attest to changing a fuel pump in
> the parking lot of a FLAPS
> (150 miles from home, 1 hour start to finish), in which the old fuel
> pump beget an appreciable amount of sand when running the pump in
> reverse on a bench test. Also, I change my square pre-filter at every
> oil change and I have a post-filter ("oil can" size) as well. Cutting
> open the pre-filter recently showed a modest amount of dirt and sand (not much rust, however).
>
> Specifically, the tanks for the "early Vanagons" come with 7mm exit
> while the "more recents" (post '85/'86?) come with a 12 mm exit. It
> seems in all cases that the 12mm exit is preferable. Though the input
> to the square pre-filter is 7mm, perhaps one could run the post-filter
> exclusively or source a 12 mm input pre-filter.
>
> If all of the above is true, then does one of our friendly e-vendors
> carry a fuel tank that would be acceptable for an '84 and have a 12mm
> exit? Do the fuel tanks for the newer Vanagons fit perfectly to an '84?
>
> All of my chatter is based on the theory that a 12 mm outlet is a
> better idea than a 7mm outlet. Is there a majority opinion toward this theory?
>
> Thanks,
>
> Skip '84 Westy, 2.2L GoWesty kit in a 1.9L case (bought the kit and
> had local (Chicago) hot rod machine shop install - did a nice job)
> -------------------------
> Thanks for the inside scoop on the sender tabs, Stuart.
> Stuart said,
> "Got mine from Van Café along with all the bits. Rock Auto sells
> them too, but they may be too cheap to be any good. Be careful
> installing the sender--the tabs on the tank "twist lock" need to be
> raised a bit on the leading corners so the sender can be twisted in.
> On mine with a new O-ring the plastic sender flange hit the edge and would not twist in, and
> you risk damaging the sender if you try to force it. Stuart"
>
|