Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (October 2013, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Sat, 12 Oct 2013 14:21:28 -0400
Reply-To:     Michael <mbucchino@CHARTER.NET>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Michael <mbucchino@CHARTER.NET>
Subject:      Re: Tips and Tricks Request - Change fuel hose from tank to pump
Comments: To: Jim Felder <jim.felder@GMAIL.COM>
In-Reply-To:  <CAFnDXk3mPEbaD5u45ute=90LoFOW6mwAgy4jM1O=QAK2qa4Wxw@mail.gmail.com>
Content-Type: text/plain; charset=us-ascii

I use a line clamp or vice grips on rubber hoses. I use a plugged coupling on hard lines. You ca easily make a plug by crimping an old cutoff piece of hard line with the threaded end still on it.

Sent from my iPhone

> On Oct 12, 2013, at 13:50, Jim Felder <jim.felder@GMAIL.COM> wrote: > > This sounds like something that Felder Enterprises could handle... > > Jim > > >> On Sat, Oct 12, 2013 at 12:24 PM, Larry Alofs <lalofs@gmail.com> wrote: >> >> For a brake line you could push a short piece of hose over the end of the

>> line and then plug the hose or clamp it shut. >> >> Larry A. >> >> >> >>> On Sat, Oct 12, 2013 at 9:43 AM, Jim Felder <jim.felder@gmail.com> wrote: >>> >>> Don, >>> >>> How do you use them to stop brake lines? I find I have to take a dowel and >>> sharpen it in a pencil sharpener to get a decent fit into a brake line, >>> and >>> even then the point is so delicate that it wants to break off, and then I

>>> have to retrieve. A better way of stopping brake fluid leaking from brake >>> and clutch fittings has been on my mind lately, having encountered a bunch >>> of it while working on the suspension. >>> >>> What do others do? >>> >>> Jim >>> >>> >>>> On Sat, Oct 12, 2013 at 7:52 AM, Don Hanson <dhanson928@gmail.com> wrote: >>>> >>>> I haven't followed the whole thread, but golf tees are handy stoppers >>> when >>>> working on fuel hoses. I have a few in all my tool kits and often use

>>>> them to stop gas or brake fluid, >>>> >>>> >>>>> On Sat, Oct 12, 2013 at 4:43 AM, Larry Alofs <lalofs@gmail.com> wrote:

>>>>> >>>>> I have a collection of rubber stoppers "left over" from when I taught >>>>> chemistry. The smallest: 000 and 00 are often useful for plugging >>> things >>>>> like the outlet from a fuel tank temporarily. I believe that these >>> are >>>>> available at Lowes and certainly at a good hardware store. A larger >>> one >>>>> (#8?) can be used to plug the filler tube grommet on a fuel tank >>> while it >>>>> is being raised into position. >>>>> Hoses can be clamped without much stress by using small needle-nosed >>>> vise >>>>> grips with pieces of hose on the jaws. >>>>> >>>>> Larry A. >>>>> did you actually find 11 mm fuel hose at your FLAPS? >>>>> >>>>> >>>>> >>>>> On Fri, Oct 11, 2013 at 6:54 PM, JRodgers <jrodgers113@gmail.com> >>> wrote: >>>>> >>>>>> Now I have the hose - next question. >>>>>> >>>>>> How would one go about replacing that hose with fuel in the tank?? >>>>>> >>>>>> Can't clamp the hose - it has to come off. Figure there must be a >>>>>> procedure to get this change done and not make a complete firebomb >>>>>> waiting to be lit! >>>>>> >>>>>> Thanks, >>>>>> >>>>>> John >>>>>> >>>>> >>>> >>> >> >>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.