Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2014, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 7 Feb 2014 12:53:51 -0800
Reply-To:     Neil N <musomuso@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Neil N <musomuso@GMAIL.COM>
Subject:      Re: Exhaust Bushing Inner Weave Premature Failure
Comments: To: Don Hanson <dhanson928@gmail.com>
In-Reply-To:  <CAHTkEuJ1sHgiAWcbud6K0=ZK=KAkVfCo8UGRURpsAoo4kpLAgw@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

No doubt. I can see that movement even after one tack onto two plates.

I aligned and mounted the muffler-cat assembly first then built the join between downpipe and J pipe. On the muffler brackets I made, some of the holes were enlarged to allow adjustment. This certainly helped the recent repair done in the muffler shop in Florence.

The challenging part in making the exhaust, was making accurate marks and keeping them aligned during fabrication. I would make marks, then remove cat and downpipe, tack the parts in basement, mount and check fit, repeat as needed. A real PITA. Welding parts in situ is best but not really feasible in my case.

Part of what I attempted to do was use parts that might be found in the junk yard. (eg total downpipe-cat assembly). This was done to help others as my WAG is that these parts can be found in good shape and had for a good price. IIRC, I paid $50 for this near new part:

https://lh5.googleusercontent.com/-Q8RL7ZfES7A/Tt1_miL9h3I/AAAAAAAAFb4/SrFznBdv3wg/s1000/Jetta%25202002-2003%2520Downpipe%253Acat.jpg

assembly before bushing install

https://lh4.googleusercontent.com/-2tXy_bqA1SQ/UPYtUkEbT2I/AAAAAAAAGlY/2JwxaYgZm-8/s720/ABA%2520Downpipe%2520To%2520Cat.jpg

https://lh6.googleusercontent.com/-xEuPuiwGAWY/UboIAjZB2cI/AAAAAAAAHuI/13iua_Y1m2s/s600/flex%2520pipe%2520install.jpg

On 2/7/14, Don Hanson <dhanson928@gmail.com> wrote:

> Welding something can induce stress and misalignment. I was shown > this....pretty large movements were apparent as the welder worked. On > something as long and obviously vulnerable to stress as the exhaust systems > on in lines seem to be, I'm guessing that it is common to screw up the > exhaust with careless welding and leave it with welded-in stresses that > lead to fairly quick cracking in a lot of cases. -- Neil n

Blog: tubaneil.blogspot.ca

'88 Westy http://tinyurl.com/c8rlw6p

'81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/

Vanagon VAG *Gas* inline-VR Engine Swap Group:

http://tinyurl.com/d7gd5ej


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.