Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (April 2014, week 3)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 17 Apr 2014 09:20:32 -0500
Reply-To:     mcneely4@COX.NET
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Dave Mcneely <mcneely4@COX.NET>
Subject:      Re: clutch chatter fixed, thanks
Comments: To: JRodgers <jrodgers113@gmail.com>
In-Reply-To:  <qsTN1n01C0wkeAR01sTPx3>
Content-Type: text/plain; charset=utf-8

I asked Darrell if he had resurfaced the flywheel. He said that it was not damaged, having neither heat damage nor any surface imperfections. As he put it, it was "as smooth as a baby's butt." mcneely

---- JRodgers <jrodgers113@gmail.com> wrote: > Dave, > > You didn't mention it, but with that many miles on the clutch the fly > wheel would surely have needed refacing. Did you have the flywheel face > machined back smooth? If so, did the pilot shaft flywheel bushing that > mounts inside the flywheel get put back in - or if missing was a new one > installed?? This bushing is extremely important because it is what > holds the pilot bearing felt washer in place. Without it - the washer > will crumble away and the garbage and debris from the clutch will > destroy the pilot bearing. It is an item often missed, > > > John > > On 4/16/2014 10:23 PM, Dave Mcneely wrote: > > Thanks to everyone who provided information and advice concerning the clutch chatter I was experiencing with my 1991 Volkswagen Vanagon GL Campmobile with manual transmission and 2.1 liter waterboxer. > > > > Thanks to Darrell Cook, whose shop in Norman, Oklahoma is listed in the Road Haus shop list, I now have a new, smooth as butter clutch. I got the needed parts from Bus Depot. The problem was that the main shaft seal on the transmission had failed, bathing the clutch with 90W gear oil. The pilot bearing had also partially seized, perhaps because the felt seal had disintegrated, allowing crud into the bearing. The van, with 174k miles, had the original clutch, at least the clutch plate and the pressure plate had VW/Audi marks on them, and Darrell said they were original. Even so, there was some material left on the clutch plate, which was chattering mainly due to the oil on it. The original fork (yoke, whatever) was still perfectly sound, as Darrell said it likely would be, as his experience is that this part wears little on the later model Vanagons. While there, Darrell also installed a new flywheel seal and o-ring, which had seen better days, with some seapage, though not t > he cause of the clutch being oiled. > > > > Thanks again to everyone. > > > > mcneely > >

-- David McNeely


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.