Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (May 2014, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 1 May 2014 08:23:54 -0600
Reply-To:     Gnarlodious <gnarlodious@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Gnarlodious <gnarlodious@GMAIL.COM>
Subject:      Re: Brakes- the saga continues
In-Reply-To:  <53624E6C.8070203@charter.net>
Content-Type: text/plain; charset=ISO-8859-1

One big advantage of the vacuum method is that microscopic bubbles expand under vacuum, causing them to flocculate faster and rise to the top sooner. I've noticed with pressure bleeding it can take some time to get microscopic air out of the system. If you watch fluid through a clear tube you see cloudy brake fluid coming out under pressure, but that just means microscopic air bubbles are incorporated in the fluid.

As a wild guess, I would say that one large bubble has more compressibility than a million small bubbles totaling the same volume of air. That would explain why your Vanagon's brakes feel fine immediately after bleeding but a few days later they are all squishy. This has happened to me several times and is something of a mystery. Someone more versed in physics could dig up the facts, I nominate Alistair Bell.

-- Gnarlie

On Thu, May 1, 2014 at 7:38 AM, Mike B <mbucchino@charter.net> wrote: > Regarding the brake bleeding process. It all depends on you method used. > If you use a Motive pressure bleeder, it's a simple one-man process, > and it's hard to "do it wrong". > If you use a vacuum hand-held, hand operated brake suction device, > you need to grease the threads of each bleeder to prevent suction of air > through the threads, but otherwise, it's also pretty hard to "do it wrong". > If you do it the old-fashioned 2-man way, there's a way to do it > wrong and a way to do it right. The right way to do it is to attach an > 18" rubber hose to the bleeder and put it in a small plastic or glass > jar with a inch or so of brake fluid in it. (you could also buy a '1-man > brake bleeder' tool, which is basically this). One guy does the pump > and hold on the pedal, while the other guy opens the bleeder and watches > the fluid/ air squirting into the jar. Repeat on each wheel until > there's no more bubbles, being sure to stop every so often to check that > the reservoir isn't getting too low. Use 3 sharp quick pedal strokes to > force air from all of it's hiding places, then hold until instructed to > let go by the guy manning the bleeders. Start at the farthest away > (right rear), then move to the next farthest bleeder (left rear), then > right front, then left front. You may need to go around them two or > three times to get it all, and a hard pedal with no squishiness is an > indicator that you're done. Be sure to do enough to clean all of the old > dark fluid out and replace it with fresh clear fluid. > If you do it without the jar and hose, you will make a mess of > spilled fluid everywhere (it eats paint!), have lots of problems (like > Don mentions) and depending on your methods and procedures, you may not > be able to get every last bubble of air out of the system. > > Mike B. > > > On 5/1/2014 9:17 AM, Don Hanson wrote: >> >> Squshy brakes: Bleeding the system carefully should stop that. >> "Carefully" being the operative word...Brake bleeding is intolerant of >> sloppy or slipshod work....any lapse at all during the brake bleeding >> process can render the whole procedure a waste of time...It can be a >> tedious job, relatively simple in concept but one that demands you make no >> mistakes along the way...It takes a fraction of a second of inattention to >> allow a bit of air to enter the hydraulics...a very very small bubble of >> air anywhere in the system will cause the spongy brake pedal feel.. >> >> Another symptom you may be encountering here is warped rotors, >> oscillating as the wheel turns, a wobble that pushs the brake pistons way >> back into calipers. So rather than an actual 'soft pedal' from air in >> the >> system, you may be needing to give the brakes a few pumps to move that >> brake pad back to where it will actually grip the warped rotor...


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.