Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (August 2014, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:   Wed, 6 Aug 2014 20:58:06 -0700
Reply-To:   Don Hanson <dhanson928@GMAIL.COM>
Sender:   Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:   Don Hanson <dhanson928@GMAIL.COM>
Subject:   Digifant II O2 sensor....My questions answered...
Comments:   To: "Vanagons and VW Buses (Bays) with VW inline gas engines" <vanagons-with-vw-inline-4-cylinder-gas-engines@googlegroups.com>
Content-Type:   text/plain; charset=UTF-8

The vehicle and motor..84 Vanagon with Inline VW...a 92 cabriolet 1.8 liter head and everything else mounted on a 93 2.0 liter ABA block. I kept the digifant engine management and used the 1.8 liter head because it fits into the vanagon using VW diesel engine mounting system and no bumps or raised rear deck..A lot of the parts are directly from a vanagon digifant system...

So my O2 sensor failed...perhaps because the wiring is/was aged and brittle and maybe shorting out....I had another spare one. the same 4 wires but not the VW plug. "We" deduced that the plug I had been running matched the 92 Cabriolet wiring diagrams...so anyhow I wired in the other 4 wire O2 sensor and that worked fine for a few days, then IT failed also, or the wires shorted out again, or perhaps the wires shorted out and caused the second O2 sensor to fail also...I don't know for sure, but that seems likely.

I looked for that particular O2 sensor with the proper plug, briefly, but after seeing them priced way up there ($75+) and considering the state of the wiring from my engine harness out to the existing plug...I decided to simplify with a less expensive single wire Bosch.(<$30) I got one from our Van Cafe California Vanagon supplier, who's tech told me it would work just fine...and so it did/does. I had a question on whether to attach the old ground wire from my computer to something...nobody really seemed to know, for sure..so I capped it off, along with the two wires to the heating element, which the single wire Bosch does without, also.

So I eliminated that sketchy plug and 3 rotten wires and simply spliced to the signal wire, after cutting back that shielding a little to get to wires in decent condition. The van ran just fine without any O2 sensor connected, but very rich and my fuel mileage dropped to just 18mpg.. In order to know if the O2 sensor I installed, rather than trying to test pin outs or millivolts with a meter, I figured I'd just run a tank of fuel through and see how far I got, thereby knowing if the sensor was working, and if there was any decline in function using a single wire one rather than the expensive heated one that cost about 4 times more. Happy to report that I am back to my previous long time confirmed fuel consumption with this tank giving me 25mpg driving some city but mostly rural..

I do not have a cat convertor in my system and the O2 sensor is right near the exhaust manifold, so it heats up quickly, I guess, judging by no decline in fuel economy...

Thanks to all who tried to help me with this...electronics in the engine are not my forte... and I have to say any time I can eliminate 3 wires and two plugs without any downside...I am all for that.


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.