Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (September 2014, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 8 Sep 2014 13:39:56 -0700
Reply-To:     Neil N <musomuso@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Neil N <musomuso@GMAIL.COM>
Subject:      Re: Travel Weirdness (warning; tires. ;)
Comments: To: "SDF ( aka ,jim lahey' - Scott )" <scottdaniel@turbovans.com>
In-Reply-To:  <540A2FF1.2020508@turbovans.com>
Content-Type: text/plain; charset=UTF-8

Hi all. Thanks much for the responses.

Of note, the old Jetta ECU I rplaced, had som serious burns on a few small components and a copper ground trace. You can see where this circuit board trace arced to the multi pin connector frame; it's likely that electricity jumped the 1/4" gap between these two parts as it may be that this frame part grounds to the vehicle chassis. Ironically, engine still ran "ok" but has always had a mysterious intermittent lack of power )felt like timing retarded) with a more recent slight surge under load at higher PRMs. New ecu is working fine. Better power, and at last check, 1.5 MPG better fuel efficiency.

Go figure. ;)

True, it was risky, and you've made an important point, but when I saw the circuit board burns on the old ECU, swapping ECUs was a no brainer; I compare and inspected the new used ECU to old one before installing. Before firing up the engine with the new ECU, i made sure the fuel pump primed and that the MIL light came on, ignition on, engine off.

Neil.

PS. thinking now, I recall that in the OEM application, the Jetta ECU mount bracket may be insulated from the vehicle frame! The way I mounted it in my vanagon, this bracket is "grounded" to the vehicle frame.

Is this incorrect?

Hope this post made sense. Am using an iPad mini to compose it. Thanks.

On Friday, September 5, 2014, SDF ( aka ;jim lahey' - Scott ) < scottdaniel@turbovans.com> wrote:

> I'll agree with that too .. > for welding on the rig....disconnect all batteries and ecu plugs. > > Don't know if the rig was running fine on the trip before swapping out > the ecu ... > but if it was.. > I sorta have this rule when on a trip ...don't work on stuff unless > there is a problem . >

-- Neil n

Blog: tubaneil.blogspot.ca

'88 Westy http://tinyurl.com/c8rlw6p

'81 VanaJetta 2.0 "Jaco" http://tubaneil.googlepages.com/

Vanagon VAG *Gas* inline-VR Engine Swap Group:

http://tinyurl.com/d7gd5ej


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.