Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2015, week 1)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Mon, 2 Feb 2015 15:46:06 -0800
Reply-To:     Neil N <musomuso@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Neil N <musomuso@GMAIL.COM>
Subject:      Re: Canadian Westfalia Shore Power Cord Warning
Comments: To: Dennis Haynes <d23haynes57@hotmail.com>
In-Reply-To:  <BAY405-EAS1076B4015AD4805A0A885B2A03C0@phx.gbl>
Content-Type: text/plain; charset=UTF-8

I agree; the failed plug on that '88 may well be a replacement. It doesn't look like the one I removed off my '81 Westy. If I recall, the plug on my '81 was molded to the outer layer of the cable; there was no metal clamp.

I tested the campground outlet before plugging into it. It tested good. All I've ever run on that '88 110VAC system is a small heater, usually on low setting. But thanks Dennis. I'll double check polarity of the system on the vehicle shore power parts. The OEM Westy circuit breaker is present. The green ground wire is properly bonded to the OEM terminal on body located behind the Westy cabinets.

I have to wonder if the shore power cable on this '88 is aftermarket. It's thicker than what is installed on my '81 Westy. If it is, this may explain the connector that was used.

Can anyone tell me if the cable shown in this image: http://tinyurl.com/qaeoo7d is what's typically used in later model year Westies?

On 2/2/15, Dennis Haynes <d23haynes57@hotmail.com> wrote:

> I find it a bit hard to believe that style of plug was used for an outside > connector. You want molded weather resistant cord sets. It also looks like > some excessive current may have been involved but a bad connection can also > cause excessive heating. You need to test the following: > Do you still have the circuit breaker inside the camper? It should be 15 amp > since the interior wiring is 14 gauge. > Is the polarity correct? The breaker needs to be on the hot, (black) wire. > Was the polarity correct at the campsite? Get yourself one of plug in > testers to test polarity and ground. > Is the body of the van properly bonded to the ground connection? > > Dennis

-- Neil n

Blog: Vanagons, Westfalia, general <http://tubaneil.blogspot.ca>

1988 Westy Images <https://picasaweb.google.com/musomuso/New1988Westy>

1981 Westfalia "Jaco" Images, technical <http://tubaneil.googlepages.com/>

Vanagon-Bus VAG Gas Engine Swap Group <http://tinyurl.com/khalbay>


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.