Vanagon EuroVan
Previous messageNext messagePrevious in topicNext in topicPrevious by same authorNext by same authorPrevious page (February 2015, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Fri, 12 Feb 2016 19:27:32 -0500
Reply-To:     Larry Alofs <lalofs@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         Larry Alofs <lalofs@GMAIL.COM>
Subject:      Re: Cooling system questions
Comments: To: Rick Cooper <rickdcooper@gmail.com>
In-Reply-To:  <CAG12ait4s6cPgf6U87+4_g8gb3JW72BD=NwBQVrij=KnJ=PLXA@mail.gmail.com>
Content-Type: text/plain; charset=UTF-8

Rick, If you haven't become familiar with the bleeder bolt on the top of the radiator it is certainly time that you did so. Remove your upper grill and you will see it at the upper corner of the radiator on the passenger side. If it is the original screw, you do not need to remove it completely to allow the air to escape; just screw it out about 3 threads or so. To bleed out air the system must have pressure in it; else you will just be letting in more air. If the pressure cap on your expansion tank works properly there will be pressure whenever the system is fully warm. Else you have to add pressure by some other means. When the system is hot and pressurized, crack open the bleeder and listen for escaping air and watch for coolant flow. Close it back up and repeat again later if you wish. This is an essential step any time the cooling system has been opened. A significant amount of air in the top part of the radiator can cetainly reduce its effectiveness and cause high operating temperatures.

Larry A.

On Fri, Feb 12, 2016 at 7:12 PM, Rick Cooper <rickdcooper@gmail.com> wrote:

> Two days ago I replaced the big coolant pipe that runs along the LH side of > the engine (from pump to thermostat area) since it had rust bubbles > happening. Put on a nice shiny stainless steel one from Frank Condelli ( > > http://www.frankcondelli.com/staging1/store/index.php?route=product/product&path=61_93_95&product_id=367 > ). > At the same time I put in a new thermostat rated for 87 degrees C, > though I'm not sure why -- guess I was tired of a lousy heater. > > Yesterday I did a 100 mile journey and the temp gauge stayed around the 3/4 > to 7/8 position, maybe a needle's width from the high end of the gauge. > This seems high, from what I've read here. I'm wondering whether I've bled > all the air out of the cooling system and it is running inefficiently. I > lost about a gallon of coolant in replacing the pipe and think I've > replaced about that much. I also topped up the reservoir a couple times > after warming up the engine. This morning (day after my journey), the > reservoir was down a couple of inches so I've topped it up again. > > But I've read here about raising the front of the vehicle and removing a > bleeder cap on the rad. Should I do that and add coolant there? > > Thanks, Rick >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.