Date: Thu, 5 Mar 2015 18:11:44 -0500
Reply-To: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Sender: Vanagon Mailing List <vanagon@gerry.vanagon.com>
From: Dennis Haynes <d23haynes57@HOTMAIL.COM>
Subject: Re: .9 bar oil pressure sender replacement
In-Reply-To: <CAHQe0n4Mo7kQpGaukA2AJK-chK7bOU4E-T2q-8OnJYEpNifvHQ@mail.gmail.com>
Content-Type: text/plain; charset="UTF-8"
If you didn’t feel ripped off paying for it is after market.
The dealer list price was $27.50 last time I bought some. The pressure settings have been revised with a significant dead band between closing and opening. They close at 1.05 bar (easy to get cold engine) and don’t open until .75 Bar. This eliminates the falsies. If you can’t maintain .75 bar ( ~10.5 psi) at 2,000 rpm you need to know.
Dennis
-----Original Message-----
From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf Of Kevin Duvernay
Sent: Thursday, March 5, 2015 12:19 PM
To: vanagon@GERRY.VANAGON.COM
Subject: Re: .9 bar oil pressure sender replacement
Thanks guys. How do I tell if my sensor is an aftermarket one or one of the genuine resigned ones?
I do have a spare oil cooler O ring kicking around somewhere, I'll dig it out. Good tip on the PB blaster. I snapped a stud replacing the other header... (although the 2/4 header hardware looks much less corroded and I've already broke 3 of the 4 nuts loose)
On Thu, Mar 5, 2015 at 11:12 AM, OlRivrRat <OlRivrRat@comcast.net> wrote:
> Kevin
>
> Not that it is necessary, but I'll put a 2nd on what DH & KW
> have said & Add that if
>
> You have not already done so, You should Soak All the Nuts&Bolts that
> you are going to
>
> be removing on this project with PBBlaster &Or Zep45 Today & then
> HeatItUp ToOp'Temp
>
> &Then SoakAgain ~
>
> &Also ~ The NextTime You change Your Oil, Save Yourself some
> UnnecessarilySpent
>
> $s & use Valvoline FullSynthetic Instead ~
>
>
> http://www.valvoline.com/products/consumer-products/motor-oil/full-syn
> thetic-motor-oil/
>
> Redline is a GreatOil as are RoyalPurple & Ams but
> WayOverPriced & a Valvo' F'S'Oil
>
> will DoTheJob JustAsWell ~
>
> There are Other Good F'S'Oils out there but I'm just fond of
> Valvo' ~
>
> ORR ~ DeanB
>
>
> On 5 Mar , 2015, at 8:50 AM, Kevin Duvernay wrote:
>
> > I'm swapping out my motor mounts tomorrow. While I'm there I'm also
> > going to replace the #2/4 header. If that goes smoothly, I've also
> > got a new water pump along with all new coolant pipes/gaskets and
> > hoses (its basically the last bits of my complete cooling system
> > overhaul!)
> >
> > Anyways, I figured while I'm there doing all this I minus well toss
> > in a new high pressure oil sender (the grey one, .9 bar). What I'm
> > wondering
> is,
> > is it possible to do this without loosing too much oil? I JUST
> > changed
> the
> > oil out to some really expensive Redline synthetic stuff, would hate
> > to waste any of it...
> >
> > Also, anything else I should address while I'm back there?
> >
> > Kevin
>
>
|