Would love to have you. We have some first rate barbeque houses here in Birmingham. Continuing on with the throttle switch adjustment, I have goe ahead and done some tweaking. I'm using the light on my ECU monitor instead of a multimeter. Does the same thing. Light on at idle, light on at full throttle, light off in between. I can get the full throttle light to work properly. It goes off as the throttle moves to idle. The idle stop is a problem. At idle, I can adjust it until the light just comes on - as it should at idle per BENTLEY. But when I move the throttle from idle to full throttle and back, the light will not come back on asit should. The setting is off just a hair, just enough to prevent the contact from closing the switch. Tried resetting it several times to no avail. I'm open to suggestions at this point. Thanks, John On Jul 10, 2015 5:19 PM, "Dennis Haynes" <d23haynes57@hotmail.com> wrote: > Maybe next time I drive to Florida I stop by and spend a couple days > getting you straight. You seem to be struggling more than needed. > > What do you like to drink? Are there good BBQ joints by you? > > > > Dennis > > > > > > > > *From:* John Rodgers [mailto:jrodgers113@gmail.com] > *Sent:* Friday, July 10, 2015 6:13 PM > *To:* Dennis Haynes > *Subject:* RE: Fuel pump fuse -''88 Gs, > > > > I'm going to do some testing and adjusting of my throttle switch and > didn't want the fuel system pressurized while I doing it. > > John > > On Jul 10, 2015 5:07 PM, "Dennis Haynes" <d23haynes57@hotmail.com> wrote: > > Depends on what you are trying to test. The fuel pump supply is shared > with power to the injectors. Since the pump only runs when the engine is > running or during cranking I am hard pressed to figure out what testing you > are doing that it needs to be disabled. You can disconnect a wire right at > the pump. There should also be a connector near the air filter that can be > disconnected. > > > > Dennis > > > > *From:* John Rodgers [mailto:jrodgers113@gmail.com] > *Sent:* Friday, July 10, 2015 3:10 PM > *To:* Dennis Haynes > *Subject:* RE: Fuel pump fuse -''88 Gs, > > > > Thanks, Dennis. > > That being the case, pulling the relay should do it, leaving all else > intact to operate? Just need that pump electrically disengaged. > > John > > John > > On Jul 10, 2015 1:56 PM, "Dennis Haynes" <d23haynes57@hotmail.com> wrote: > > The fuel pump, ignition system, and the ECU are not fused. > > Dennis > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf > Of John Rodgers > Sent: Friday, July 10, 2015 2:45 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Fuel pump fuse -''88 Gs, > > I need to disable the fuel pump but can only find the relay. Need to pull > the fuse and do some testing. An assistance would be appeciated! > > Thanks, > > John > > |
Please note - During the past 17 years of operation, several gigabytes of
Vanagon mail messages have been archived. Searching the entire collection
will take up to five minutes to complete. Please be patient!
Return to the archives @ gerry.vanagon.com
The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.
Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.