Vanagon EuroVan
Previous (more recent) messageNext (less recent) messagePrevious (more recent) in topicNext (less recent) in topicPrevious (more recent) by same authorNext (less recent) by same authorPrevious page (July 2015, week 2)Back to main VANAGON pageJoin or leave VANAGON (or change settings)ReplyPost a new messageSearchProportional fontNon-proportional font
Date:         Thu, 9 Jul 2015 21:00:56 -0500
Reply-To:     John Rodgers <jrodgers113@GMAIL.COM>
Sender:       Vanagon Mailing List <vanagon@gerry.vanagon.com>
From:         John Rodgers <jrodgers113@GMAIL.COM>
Subject:      Re: Oil pressure
Comments: To: Jeff Schwaia <vw.doka@gmail.com>, Josh Weber <jmweberga@gmail.com>
In-Reply-To:  <006201d0ba9a$88c47250$9a4d56f0$@gmail.com>
Content-Type: text/plain; charset=UTF-8

I have two engines to deal with. On the new engine, I think I will go wth the sandwich set up and two guages - oil temp and pressure.

On the old engine - 150, 000 miles - I will go with the gauge that gets pressure readings off the cam.

John On Jul 9, 2015 5:57 PM, "Jeff Schwaia" <vw.doka@gmail.com> wrote:

> Actually, the only difference between the two oil pressure locations is > that one is before the oil filter, and the other is after the oil filter. > > Cheers, > > Jeff > > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf > Of Stuart MacMillan > Sent: Thursday, July 09, 2015 3:50 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Re: Oil pressure > > I prefer the cam location simply because knowing the pressure there is the > most critical. Oil pressure leaks down at the bearings, and this measures > it at the bearings. > > Full oil pump pressure is delivered to the filter/sandwich plate, so you > will likely see a somewhat higher pressure there as the engine wears, as > compared to the bearings, but probably not much higher. > > The important thing is to watch the long term trend of the pressure drop, > which is inevitable. When you get below 8 psi at hot idle and 20 at 3000, > start saving for a new engine. Six psi at idle and you are on borrowed > time. BTDT-my experience with a used 2.1 engine: > > OIL PRESSURE: 8 psi at idle, 24 psi cruising when installed. Over the next > 10,000 miles pressure steadily dropped to 4 psi idle, 12-15 psi cruising. > At the end of the 3000 mile trip idle pressure was zero (red light came > on), cruising 8 psi. Blew up at 65 mph just 65 miles from home, still > running strong! > > I'm hoping for one more year from my current 1.9 with the same initial oil > pressure. > > Stuart > > -----Original Message----- > From: Vanagon Mailing List [mailto:vanagon@gerry.vanagon.com] On Behalf > Of John Rodgers > Sent: Thursday, July 09, 2015 2:25 PM > To: vanagon@GERRY.VANAGON.COM > Subject: Oil pressure > > I've got two oil pressure guage setups. One takes pressure from the > pressure switch that monitors oil pressure at the cam. No oil temps. It has > a pressure guage only. The other is a sandwich device that takes oil > pressure and temperature between the oil filter and oil cooler. Of these > two, which would be best. Opinions? Why? > > Thanks, > > John >


Back to: Top of message | Previous page | Main VANAGON page

Please note - During the past 17 years of operation, several gigabytes of Vanagon mail messages have been archived. Searching the entire collection will take up to five minutes to complete. Please be patient!


Return to the archives @ gerry.vanagon.com


The vanagon mailing list archives are copyright (c) 1994-2011, and may not be reproduced without the express written permission of the list administrators. Posting messages to this mailing list grants a license to the mailing list administrators to reproduce the message in a compilation, either printed or electronic. All compilations will be not-for-profit, with any excess proceeds going to the Vanagon mailing list.

Any profits from list compilations go exclusively towards the management and operation of the Vanagon mailing list and vanagon mailing list web site.